Q factor
In physics and engineering the quality factor or Q factor is a dimensionless parameter that describes how underdamped an oscillator or resonator is. It is defined as the ratio of the peak energy stored in the resonator in a cycle of oscillation to the energy lost per radian of the cycle.^{[1]} Q factor is alternatively defined as the ratio of a resonator's centre frequency to its bandwidth when subject to an oscillating driving force. These two definitions give numerically similar, but not identical, results.^{[2]} Higher Q indicates a lower rate of energy loss and the oscillations die out more slowly. A pendulum suspended from a highquality bearing, oscillating in air, has a high Q, while a pendulum immersed in oil has a low one. Resonators with high quality factors have low damping, so that they ring or vibrate longer.
ExplanationEdit
Q factor is a parameter that describes the resonance behavior of an underdamped harmonic oscillator (resonator). Sinusoidally driven resonators having higher Q factors resonate with greater amplitudes (at the resonant frequency) but have a smaller range of frequencies around that frequency for which they resonate; the range of frequencies for which the oscillator resonates is called the bandwidth. Thus, a highQ tuned circuit in a radio receiver would be more difficult to tune, but would have more selectivity; it would do a better job of filtering out signals from other stations that lie nearby on the spectrum. HighQ oscillators oscillate with a smaller range of frequencies and are more stable. (See oscillator phase noise.)
The quality factor of oscillators varies substantially from system to system, depending on their construction. Systems for which damping is important (such as dampers keeping a door from slamming shut) have Q near ^{1}⁄_{2}. Clocks, lasers, and other resonating systems that need either strong resonance or high frequency stability have high quality factors. Tuning forks have quality factors around 1000. The quality factor of atomic clocks, superconducting RF cavities used in accelerators, and some highQ lasers can reach as high as 10^{11}^{[3]} and higher.^{[4]}
There are many alternative quantities used by physicists and engineers to describe how damped an oscillator is. Important examples include: the damping ratio, relative bandwidth, linewidth and bandwidth measured in octaves.
The concept of Q originated with K. S. Johnson of Western Electric Company's Engineering Department while evaluating the quality of coils (inductors). His choice of the symbol Q was only because, at the time, all other letters of the alphabet were taken. The term was not intended as an abbreviation for "quality" or "quality factor", although these terms have grown to be associated with it. ^{[5]}^{[6]}^{[7]}
DefinitionEdit
The definition of Q since its first use in 1914 has been generalized to apply to coils and condensers, resonant circuits, resonant devices, resonant transmission lines, cavity resonators, material Q and spectral lines.^{[5]}
Resonant devicesEdit
In the context of resonators, there are two common definitions for Q, which aren't exactly equivalent. They become approximately equivalent as Q becomes larger, meaning the resonator becomes less damped. One of these definitions is the frequencytobandwidth ratio of the resonator:^{[5]}
where f_{r} is the resonant frequency, Δf is the resonance width or full width at half maximum (FWHM) i.e. the bandwidth over which the power of vibration is greater than half the power at the resonant frequency, ω_{r} = 2πf_{r} is the angular resonant frequency, and Δω is the angular halfpower bandwidth.
Under this definition, Q is the reciprocal of fractional bandwidth.
Coils and condensersEdit
The other common nearly equivalent definition for Q is the ratio of the energy stored in the oscillating resonator to the energy dissipated per cycle by damping processes:^{[8]}^{[9]}^{[5]}
The factor 2π makes Q expressible in simpler terms, involving only the coefficients of the secondorder differential equation describing most resonant systems, electrical or mechanical. In electrical systems, the stored energy is the sum of energies stored in lossless inductors and capacitors; the lost energy is the sum of the energies dissipated in resistors per cycle. In mechanical systems, the stored energy is the maximum possible stored energy, or the total energy, i.e. the sum of the potential and kinetic energies at some point in time; the lost energy is the work done by an external conservative force, per cycle, to maintain amplitude.
More generally and in the context of reactive component specification (especially inductors), the frequencydependent definition of Q is used:^{[8]}^{[10]}^{[failed verification (See discussion.)]}^{[9]}
where ω is the angular frequency at which the stored energy and power loss are measured. This definition is consistent with its usage in describing circuits with a single reactive element (capacitor or inductor), where it can be shown to be equal to the ratio of reactive power to real power. (See Individual reactive components.)
Q factor and dampingEdit
The Q factor determines the qualitative behavior of simple damped oscillators. (For mathematical details about these systems and their behavior see harmonic oscillator and linear time invariant (LTI) system.)
 A system with low quality factor (Q < ^{1}⁄_{2}) is said to be overdamped. Such a system doesn't oscillate at all, but when displaced from its equilibrium steadystate output it returns to it by exponential decay, approaching the steady state value asymptotically. It has an impulse response that is the sum of two decaying exponential functions with different rates of decay. As the quality factor decreases the slower decay mode becomes stronger relative to the faster mode and dominates the system's response resulting in a slower system. A secondorder lowpass filter with a very low quality factor has a nearly firstorder step response; the system's output responds to a step input by slowly rising toward an asymptote.
 A system with high quality factor (Q > ^{1}⁄_{2}) is said to be underdamped. Underdamped systems combine oscillation at a specific frequency with a decay of the amplitude of the signal. Underdamped systems with a low quality factor (a little above Q = ^{1}⁄_{2}) may oscillate only once or a few times before dying out. As the quality factor increases, the relative amount of damping decreases. A highquality bell rings with a single pure tone for a very long time after being struck. A purely oscillatory system, such as a bell that rings forever, has an infinite quality factor. More generally, the output of a secondorder lowpass filter with a very high quality factor responds to a step input by quickly rising above, oscillating around, and eventually converging to a steadystate value.
 A system with an intermediate quality factor (Q = ^{1}⁄_{2}) is said to be critically damped. Like an overdamped system, the output does not oscillate, and does not overshoot its steadystate output (i.e., it approaches a steadystate asymptote). Like an underdamped response, the output of such a system responds quickly to a unit step input. Critical damping results in the fastest response (approach to the final value) possible without overshoot. Real system specifications usually allow some overshoot for a faster initial response or require a slower initial response to provide a safety margin against overshoot.
In negative feedback systems, the dominant closedloop response is often wellmodeled by a secondorder system. The phase margin of the openloop system sets the quality factor Q of the closedloop system; as the phase margin decreases, the approximate secondorder closedloop system is made more oscillatory (i.e., has a higher quality factor).
Quality factors of common systemsEdit
 A unitygain Sallen–Key lowpass filter topology with equal capacitors and equal resistors is critically damped (i.e., Q = ^{1}⁄_{2}).
 A secondorder Butterworth filter (i.e., continuoustime filter with the flattest passband frequency response) has an underdamped Q = ^{1}⁄_{√2}.^{[11]}
 A Bessel filter (i.e., continuoustime filter with flattest group delay) has an underdamped Q = ^{1}⁄_{√3}.^{[citation needed]}
Physical interpretationEdit
Physically speaking, Q is 2π times the ratio of the total energy stored divided by the energy lost in a single cycle or equivalently the ratio of the stored energy to the energy dissipated over one radian of the oscillation.^{[12]}
It is a dimensionless parameter that compares the exponential time constant τ for decay of an oscillating physical system's amplitude to its oscillation period. Equivalently, it compares the frequency at which a system oscillates to the rate at which it dissipates its energy.
Equivalently (for large values of Q), the Q factor is approximately the number of oscillations required for a freely oscillating system's energy to fall off to e^{−2π}, or about ^{1}⁄_{535} or 0.2%, of its original energy.^{[13]} This means the amplitude falls off to approximately e^{−π} or 4% of its original amplitude.^{[14]}
The width (bandwidth) of the resonance is given by
where f_{0} is the resonant frequency, and Δf, the bandwidth, is the width of the range of frequencies for which the energy is at least half its peak value.
The resonant frequency is often expressed in natural units (radians per second), rather than using the f_{0} in hertz, as
The factors Q, damping ratio ζ, attenuation rate α, and exponential time constant τ are related such that:^{[15]}
and the damping ratio can be expressed as:
The envelope of oscillation decays proportional to e^{−αt} or e^{−t/τ}, where α and τ can be expressed as:
and
The energy of oscillation, or the power dissipation, decays twice as fast, that is, as the square of the amplitude, as e^{−2αt} or e^{−2tτ}.
For a twopole lowpass filter, the transfer function of the filter is^{[15]}
For this system, when Q > ^{1}⁄_{2} (i.e., when the system is underdamped), it has two complex conjugate poles that each have a real part of −α. That is, the attenuation parameter α represents the rate of exponential decay of the oscillations (that is, of the output after an impulse) into the system. A higher quality factor implies a lower attenuation rate, and so highQ systems oscillate for many cycles. For example, highquality bells have an approximately pure sinusoidal tone for a long time after being struck by a hammer.

Electrical systemsEdit
For an electrically resonant system, the Q factor represents the effect of electrical resistance and, for electromechanical resonators such as quartz crystals, mechanical friction.
Relationship between Q and bandwidthEdit
The 2sided bandwidth relative to a resonant frequency of F_{0} Hz is F_{0}/Q.
For example, an antenna tuned to have a Q value of 10 and a centre frequency of 100 kHz would have a 3 dB bandwidth of 10 kHz.
In audio, bandwidth is often expressed in terms of octaves. Then the relationship between Q and bandwidth is
where BW is the bandwidth in octaves.^{[17]}
RLC circuitsEdit
In an ideal series RLC circuit, and in a tuned radio frequency receiver (TRF) the Q factor is:^{[18]}
where R, L and C are the resistance, inductance and capacitance of the tuned circuit, respectively. The larger the series resistance, the lower the circuit Q.
For a parallel RLC circuit, the Q factor is the inverse of the series case:^{[19]}^{[18]}
 ^{[20]}
Consider a circuit where R, L and C are all in parallel. The lower the parallel resistance, the more effect it will have in damping the circuit and thus the lower the Q. This is useful in filter design to determine the bandwidth.
In a parallel LC circuit where the main loss is the resistance of the inductor, R, in series with the inductance, L, Q is as in the series circuit. This is a common circumstance for resonators, where limiting the resistance of the inductor to improve Q and narrow the bandwidth is the desired result.
Individual reactive componentsEdit
The Q of an individual reactive component depends on the frequency at which it is evaluated, which is typically the resonant frequency of the circuit that it is used in. The Q of an inductor with a series loss resistance is the Q of a resonant circuit using that inductor (including its series loss) and a perfect capacitor.^{[21]}
where:
 ω_{0} is the resonance frequency in radians per second,
 L is the inductance,
 X_{L} is the inductive reactance, and
 R_{L} is the series resistance of the inductor.
The Q of a capacitor with a series loss resistance is the same as the Q of a resonant circuit using that capacitor with a perfect inductor:^{[21]}
where:
 ω_{0} is the resonance frequency in radians per second,
 C is the capacitance,
 X_{C} is the capacitive reactance, and
 R_{C} is the series resistance of the capacitor.
In general, the Q of a resonator involving a series combination of a capacitor and an inductor can be determined from the Q values of the components, whether their losses come from series resistance or otherwise:^{[21]}
Mechanical systemsEdit
For a single damped massspring system, the Q factor represents the effect of simplified viscous damping or drag, where the damping force or drag force is proportional to velocity. The formula for the Q factor is:
where M is the mass, k is the spring constant, and D is the damping coefficient, defined by the equation F_{damping} = −Dv, where v is the velocity.^{[22]}
Acoustical systemsEdit
The Q of a musical instrument is critical; an excessively high Q in a resonator will not evenly amplify the multiple frequencies an instrument produces. For this reason, string instruments often have bodies with complex shapes, so that they produce a wide range of frequencies fairly evenly.
The Q of a brass instrument or wind instrument needs to be high enough to pick one frequency out of the broaderspectrum buzzing of the lips or reed. By contrast, a vuvuzela is made of flexible plastic, and therefore has a very low Q for a brass instrument, giving it a muddy, breathy tone. Instruments made of stiffer plastic, brass, or wood have higherQ. An excessively high Q can make it harder to hit a note. Q in an instrument may vary across frequencies, but this may not be desirable.
Helmholtz resonators have a very high Q, as they are designed for picking out a very narrow range of frequencies.
Optical systemsEdit
In optics, the Q factor of a resonant cavity is given by
where f_{o} is the resonant frequency, E is the stored energy in the cavity, and P = −dE/dt is the power dissipated. The optical Q is equal to the ratio of the resonant frequency to the bandwidth of the cavity resonance. The average lifetime of a resonant photon in the cavity is proportional to the cavity's Q. If the Q factor of a laser's cavity is abruptly changed from a low value to a high one, the laser will emit a pulse of light that is much more intense than the laser's normal continuous output. This technique is known as Qswitching. Q factor is of particular importance in plasmonics, where loss is linked to the damping of the surface plasmon resonance^{[23]}. While loss is normally considered a hindrance in the development of plasmonic devices, it is possible to leverage this property to present new enhanced functionalities^{[24]}.
See alsoEdit
ReferencesEdit
 ^ Harlow, James H. (2004). Electric power transformer engineering. CRC Press. pp. 2–216. ISBN 9780849317040. Archived from the original on 20161202.
 ^ Tooley, Michael H. (2006). Electronic circuits: fundamentals and applications. Newnes. pp. 77–78. ISBN 9780750669238. Archived from the original on 20161201.
 ^ Encyclopedia of Laser Physics and Technology: Q factor Archived 20090224 at the Wayback Machine
 ^ Time and Frequency from A to Z: Q to Ra Archived 20080504 at the Wayback Machine
 ^ ^{a} ^{b} ^{c} ^{d} Green, Estill I. (October 1955). "The Story of Q" (PDF). American Scientist. 43: 584–594. Archived from the original (PDF) on 20121203.
 ^ B. Jeffreys, Q.Jl R. astr. Soc. (1985) 26, 51–52
 ^ Paschotta, Rüdiger (2008). Encyclopedia of Laser Physics and Technology, Vol. 1: AM. WileyVCH. p. 580. ISBN 9783527408283. Archived from the original on 20180511.
 ^ ^{a} ^{b} Slyusar V. I. 60 Years of Electrically Small Antennas Theory.//Proceedings of the 6th International Conference on Antenna Theory and Techniques, 17–21 September 2007, Sevastopol, Ukraine.  Pp. 116  118. "Archived copy" (PDF). Archived (PDF) from the original on 20170828. Retrieved 20170902.CS1 maint: archived copy as title (link)
 ^ ^{a} ^{b} U.A.Bakshi, A. V. Bakshi (2006). Network Analysis. Technical Publications. p. 228. ISBN 9788189411237.
 ^ James W. Nilsson (1989). Electric Circuits. ISBN 0201172887.
 ^ Sabah, Nassir H. (2017). Circuit Analysis with PSpice: A Simplified Approach. CRC Press. p. 446. ISBN 9781315402215.
 ^ Jackson, R. (2004). Novel Sensors and Sensing. Bristol: Institute of Physics Pub. p. 28. ISBN 075030989X.
 ^ Benjamin Crowell (2006). "Light and Matter". Archived from the original on 20110519., Ch. 18
 ^ Anant., Agarwal (2005). Foundations of analog & digital electronic circuits. Lang, Jeffrey (Jeffrey H.). Amsterdam: Elsevier. p. 647. ISBN 9781558607354. OCLC 60245509.
 ^ ^{a} ^{b} Siebert, William McC. Circuits, Signals, and Systems. MIT Press.
 ^ "Analog Dialogue Technical Journal  Analog Devices" (PDF). www.analog.com. Archived (PDF) from the original on 20160804.
 ^ http://www.rane.com/note170.html
 ^ ^{a} ^{b} U.A.Bakshi; A.V.Bakshi (2008). Electric Circuits. Technical Publications. pp. 2–79. ISBN 9788184314526.
 ^ "Complete Response I  Constant Input". fourier.eng.hmc.edu. Archived from the original on 20120110.
 ^ Frequency Response: Resonance, Bandwidth, Q Factor Archived 20141206 at the Wayback Machine
 ^ ^{a} ^{b} ^{c} Di Paolo, Franco (2000). Networks and Devices Using Planar Transmission Lines. CRC Press. pp. 490–491. ISBN 9780849318351. Archived from the original on 20180511.
 ^ Methods of Experimental Physics – Lecture 5: Fourier Transforms and Differential Equations Archived 20120319 at the Wayback Machine
 ^ Tavakoli, Mehdi; Jalili, Yousef Seyed; Elahi, Seyed Mohammad (20190428). "RayleighWood anomaly approximation with FDTD simulation of plasmonic gold nanohole array for determination of optimum extraordinary optical transmission characteristics". Superlattices and Microstructures. 130: 454–471. doi:10.1016/j.spmi.2019.04.035.
 ^ Chen, Gang; Mahan, Gerald; Meroueh, Laureen; Huang, Yi; Tsurimaki, Yoichiro; Tong, Jonathan K.; Ni, George; Zeng, Lingping; Cooper, Thomas Alan (20171231). "Losses in plasmonics: from mitigating energy dissipation to embracing lossenabled functionalities". Advances in Optics and Photonics. 9 (4): 775–827. doi:10.1364/AOP.9.000775. ISSN 19438206.
Further readingEdit
 Agarwal, Anant; Lang, Jeffrey (2005). Foundations of Analog and Digital Electronic Circuits. Morgan Kaufmann. ISBN 1558607358.
External linksEdit
Wikimedia Commons has media related to Quality factor. 