Prandtl number

The Prandtl number (Pr) or Prandtl group is a dimensionless number, named after the German physicist Ludwig Prandtl, defined as the ratio of momentum diffusivity to thermal diffusivity.[1] That is, the Prandtl number is given as:


  •  : momentum diffusivity (kinematic viscosity), , (SI units: m2/s)
  •  : thermal diffusivity, , (SI units: m2/s)
  •  : dynamic viscosity, (SI units: Pa s = N s/m2)
  •  : thermal conductivity, (SI units: W/(m·K))
  •  : specific heat, (SI units: J/(kg·K))
  •  : density, (SI units: kg/m3).

Note that whereas the Reynolds number and Grashof number are subscripted with a length scale variable, the Prandtl number contains no such length scale in its definition and is dependent only on the fluid and the fluid state. The Prandtl number is often found in property tables alongside other properties such as viscosity and thermal conductivity.

For most gases over a wide range of temperature and pressure, Pr is approximately constant. Therefore, it can be used to determine the thermal conductivity of gases at high temperatures, where it is difficult to measure experimentally due to the formation of convection currents.[1]

Typical values for Pr are:

Small values of the Prandtl number, Pr << 1, means the thermal diffusivity dominates. Whereas with large values, Pr >> 1, the momentum diffusivity dominates the behavior. For example, the listed value for liquid mercury indicates that the heat conduction is more significant compared to convection, so thermal diffusivity is dominant. However, for engine oil, convection is very effective in transferring energy from an area in comparison to pure conduction, so momentum diffusivity is dominant.[2]

The Prandtl numbers of gases are about 1, which indicates that both momentum and heat dissipate through the fluid at about the same rate. Heat diffuses very quickly in liquid metals (Pr<<1) and very slowly in oils (Pr>>1) relative to momentum. Consequently thermal boundary layer is much thicker for liquid metals and much thinner for oils relative to velocity boundary layer.

In heat transfer problems, the Prandtl number controls the relative thickness of the momentum and thermal boundary layers. When Pr is small, it means that the heat diffuses quickly compared to the velocity (momentum). This means that for liquid metals the thermal boundary layer is much thicker than the velocity boundary layer.

The mass transfer analog of the Prandtl number is the Schmidt number.

Formula for the calculation of the Prandtl number of air and waterEdit

For air with a pressure of 1 bar, the Prandtl numbers in the temperature range between -100 °C and +500 °C can be calculated using the formula given below[3]. The temperature is to be used in the unit degree Celsius. The deviations are a maximum of 0.1 % from the literature values.


The Prandtl numbers for water (1 bar) can be determined in the temperature range between 0 °C and 90 °C using the formula given below[4]. The temperature is to be used in the unit degree Celsius. The deviations are a maximum of 1 % from the literature values.


See alsoEdit


  1. ^ a b c d e f g h i Coulson, J. M.; Richardson, J. F. (1999). Chemical Engineering Volume 1 (6th ed.). Elsevier. ISBN 978-0-7506-4444-0.
  2. ^ Çengel, Yunus A. (2003). Heat transfer : a practical approach (2nd ed.). Boston: McGraw-Hill. ISBN 0072458933. OCLC 50192222.
  3. ^ tec-science (2020-05-10). "Prandtl number". tec-science. Retrieved 2020-06-25.
  4. ^ tec-science (2020-05-10). "Prandtl number". tec-science. Retrieved 2020-06-25.

General referencesEdit

  • White, F. M. (2006). Viscous Fluid Flow (3rd. ed.). New York: McGraw-Hill. ISBN 0-07-240231-8.