Nuclear weapon design
- pure fission weapons, the simplest and least technically demanding, were the first nuclear weapons built and have so far been the only type ever used in an act of war (over wartime Japan).
- boosted fission weapons increase yield beyond that of the implosion design by using small quantities of fusion fuel to enhance the fission chain reaction. Boosting can more than double the weapon's fission energy yield.
- staged thermonuclear weapons are essentially arrangements of two or more "stages", most usually two. The first stage is always a boosted fission weapon as above. Its detonation causes it to shine intensely with x-radiation, which illuminates and implodes the second stage filled with a large quantity of fusion fuel. This sets in motion a sequence of events which results in a thermonuclear, or fusion, burn. This process affords potential yields up to hundreds of times those of fission weapons.
A fourth type, pure fusion weapons, is a theoretical possibility. Such weapons would produce far fewer radioactive byproducts than current designs, although they would release huge numbers of neutrons.
Pure fission weapons historically have been the first type to be built by new nuclear powers. Large industrial states with well-developed nuclear arsenals have two-stage thermonuclear weapons, which are the most compact, scalable, and cost effective option once the necessary technical base and industrial infrastructure are built.
Most known innovations in nuclear weapon design originated in the United States, although some were later developed independently by other states.
In early news accounts, pure fission weapons were called atomic bombs or A-bombs and weapons involving fusion were called hydrogen bombs or H-bombs. Practitioners, however, favor the terms nuclear and thermonuclear, respectively.
Nuclear fission separates or splits heavier atoms to form lighter atoms. Nuclear fusion combines lighter atoms to form heavier atoms. Both reactions generate roughly a million times more energy than comparable chemical reactions, making nuclear bombs a million times more powerful than non-nuclear bombs, which a French patent claimed in May 1939.
In some ways, fission and fusion are opposite and complementary reactions, but the particulars are unique for each. To understand how nuclear weapons are designed, it is useful to know the important similarities and differences between fission and fusion. The following explanation uses rounded numbers and approximations.
When a free neutron hits the nucleus of a fissile atom like uranium-235 (235U), the uranium nucleus splits into two smaller nuclei called fission fragments, plus more neutrons. Fission can be self-sustaining because it produces more neutrons of the speed required to cause new fissions.
The U-235 nucleus can split in many ways, provided the atomic numbers add up to 92 and the atomic masses add to 236 (uranium plus the extra neutron). The following equation shows one possible split, namely into strontium-95 (95Sr), xenon-139 (139Xe), and two neutrons (n), plus energy:
The immediate energy release per atom is about 180 million electron volts (MeV); i.e., 74 TJ/kg. Only 7% of this is gamma radiation and kinetic energy of fission neutrons. The remaining 93% is kinetic energy (or energy of motion) of the charged fission fragments, flying away from each other mutually repelled by the positive charge of their protons (38 for strontium, 54 for xenon). This initial kinetic energy is 67 TJ/kg, imparting an initial speed of about 12,000 kilometers per second. The charged fragments' high electric charge causes many inelastic collisions with nearby atoms, and these fragments remain trapped inside the bomb's uranium pit and tamper until their motion is converted into heat. This takes about a millionth of a second (a microsecond), by which time the core and tamper of the bomb have expanded to plasma several meters in diameter with a temperature of tens of millions of degrees Celsius.
This is hot enough to emit black-body radiation in the X-ray spectrum. These X-rays are absorbed by the surrounding air, producing the fireball and blast of a nuclear explosion.
Most fission products have too many neutrons to be stable so they are radioactive by beta decay, converting neutrons into protons by throwing off beta particles (electrons) and gamma rays. Their half lives range from milliseconds to about 200,000 years. Many decay into isotopes that are themselves radioactive, so from 1 to 6 (average 3) decays may be required to reach stability. In reactors, the radioactive products are the nuclear waste in spent fuel. In bombs, they become radioactive fallout, both local and global.
Meanwhile, inside the exploding bomb, the free neutrons released by fission carry away about 3% of the initial fission energy. Neutron kinetic energy adds to the blast energy of a bomb, but not as effectively as the energy from charged fragments, since neutrons are not slowed as quickly. The main contribution of fission neutrons to the bomb's power is the initiation of other fissions. Over half of the neutrons escape the bomb core, but the rest strike U-235 nuclei causing them to fission in an exponentially growing chain reaction (1, 2, 4, 8, 16, etc.). Starting from one atom, the number of fissions can theoretically double a hundred times in a microsecond, which could consume all uranium or plutonium up to hundreds of tons by the hundredth link in the chain. In practice, bombs do not contain hundreds of tons of uranium or plutonium. Instead, typically (in a modern weapon) the core of a weapon contains only about 5 kilograms of plutonium, of which only 2 to 2.5 kilograms, representing 40 to 50 kilotons of energy, undergoes fission before the core blows itself apart.
Holding an exploding bomb together is the greatest challenge of fission weapon design. The heat of fission rapidly expands the fission core, spreading apart the target nuclei and making space for the neutrons to escape without being captured. The chain reaction stops.
Materials which can sustain a chain reaction are called fissile. The two fissile materials used in nuclear weapons are: U-235, also known as highly enriched uranium (HEU), oralloy (Oy) meaning Oak Ridge Alloy, or 25 (the last digits of the atomic number, which is 92 for uranium, and the atomic weight, here 235, respectively); and Pu-239, also known as plutonium, or 49 (from 94 and 239).
Uranium's most common isotope, U-238, is fissionable but not fissile (meaning that it cannot sustain a chain reaction by itself but can be made to fission with fast neutrons). Its aliases include natural or unenriched uranium, depleted uranium (DU), tubealloy (Tu), and 28. It cannot sustain a chain reaction, because its own fission neutrons are not powerful enough to cause more U-238 fission. The neutrons released by fusion will fission U-238. This U-238 fission reaction produces most of the energy in a typical two-stage thermonuclear weapon.
Fusion produces neutrons which dissipate energy from the reaction. In weapons, the most important fusion reaction is called the D-T reaction. Using the heat and pressure of fission, hydrogen-2, or deuterium (2D), fuses with hydrogen-3, or tritium (3T), to form helium-4 (4He) plus one neutron (n) and energy:
The total energy output, 17.6 MeV, is one tenth of that with fission, but the ingredients are only one-fiftieth as massive, so the energy output per unit mass is approximately five times as great. In this fusion reaction, 14 of the 17.6 MeV (80% of the energy released in the reaction) shows up as the kinetic energy of the neutron, which, having no electric charge and being almost as massive as the hydrogen nuclei that created it, can escape the scene without leaving its energy behind to help sustain the reaction – or to generate x-rays for blast and fire.
The only practical way to capture most of the fusion energy is to trap the neutrons inside a massive bottle of heavy material such as lead, uranium, or plutonium. If the 14 MeV neutron is captured by uranium (of either isotope; 14 MeV is high enough to fission both 235U and 238U) or plutonium, the result is fission and the release of 180 MeV of fission energy, multiplying the energy output tenfold.
For weapon use, fission is necessary to start fusion, helps to sustain fusion, and captures and multiplies the energy carried by the fusion neutrons. In the case of a neutron bomb (see below), the last-mentioned factor does not apply, since the objective is to facilitate the escape of neutrons, rather than to use them to increase the weapon's raw power.
A third important nuclear reaction is the one that creates tritium, essential to the type of fusion used in weapons. Tritium, or hydrogen-3, is made by bombarding lithium-6 (6Li) with a neutron (n). This neutron bombardment will cause the lithium-6 nucleus to split, producing helium-4 (4He) plus tritium (3T) and energy:
A nuclear reactor is necessary to provide the neutrons if the tritium is to be provided before the weapon is used. The industrial-scale conversion of lithium-6 to tritium is very similar to the conversion of uranium-238 into plutonium-239. In both cases the feed material is placed inside a nuclear reactor and removed for processing after a period of time.
Alternatively, neutrons from earlier stage fusion reactions can be used to fission lithium-6 (in the form of lithium deuteride for example) and form tritium during detonation. This approach reduces the amount of tritium-based fuel in a weapon.
The fission of one plutonium atom releases ten times more total energy than the fusion of one tritium atom. For this reason, tritium is included in nuclear weapon components only when it causes more fission than its production sacrifices, namely in the case of fusion-boosted fission.
Of the four basic types of nuclear weapon, the first, pure fission, uses the first of the three nuclear reactions above. The second, fusion-boosted fission, uses the first two. The third, two-stage thermonuclear, uses all three.
Pure fission weaponsEdit
The first task of a nuclear weapon design is to rapidly assemble a supercritical mass of fissile uranium or plutonium. A supercritical mass is one in which the percentage of fission-produced neutrons captured by another fissile nucleus is large enough that each fission event, on average, causes more than one additional fission event.
Once the critical mass is assembled, at maximum density, a burst of neutrons is supplied to start as many chain reactions as possible. Early weapons used a modulated neutron generator codenamed "Urchin" inside the pit containing polonium-210 and beryllium separated by a thin barrier. Implosion of the pit crushed the neutron generator, mixing the two metals, thereby allowing alpha particles from the polonium to interact with beryllium to produce free neutrons. In modern weapons, the neutron generator is a high-voltage vacuum tube containing a particle accelerator which bombards a deuterium/tritium-metal hydride target with deuterium and tritium ions. The resulting small-scale fusion produces neutrons at a protected location outside the physics package, from which they penetrate the pit. This method allows better control of the timing of chain reaction initiation.
The critical mass of an uncompressed sphere of bare metal is 50 kg (110 lb) for uranium-235 and 16 kg (35 lb) for delta-phase plutonium-239. In practical applications, the amount of material required for criticality is modified by shape, purity, density, and the proximity to neutron-reflecting material, all of which affect the escape or capture of neutrons.
To avoid a chain reaction during handling, the fissile material in the weapon must be sub-critical before detonation. It may consist of one or more components containing less than one uncompressed critical mass each. A thin hollow shell can have more than the bare-sphere critical mass, as can a cylinder, which can be arbitrarily long without ever reaching criticality.
A tamper is an optional layer of dense material surrounding the fissile material. Due to its inertia it delays the expansion of the reacting material, increasing the efficiency of the weapon. Often the same layer serves both as tamper and as neutron reflector.
Gun-type assembly weaponEdit
Little Boy, the Hiroshima bomb, used 64 kg (141 lb) of uranium with an average enrichment of around 80%, or 51 kg (112 lb) of U-235, just about the bare-metal critical mass. (See Little Boy article for a detailed drawing.) When assembled inside its tamper/reflector of tungsten carbide, the 64 kg (141 lb) was more than twice critical mass. Before the detonation, the uranium-235 was formed into two sub-critical pieces, one of which was later fired down a gun barrel to join the other, starting the nuclear explosion. Analysis shows that less than 2% of the uranium mass underwent fission; the remainder, representing most of the entire wartime output of the giant Y-12 factories at Oak Ridge, scattered uselessly.
The inefficiency was caused by the speed with which the uncompressed fissioning uranium expanded and became sub-critical by virtue of decreased density. Despite its inefficiency, this design, because of its shape, was adapted for use in small-diameter, cylindrical artillery shells (a gun-type warhead fired from the barrel of a much larger gun). Such warheads were deployed by the United States until 1992, accounting for a significant fraction of the U-235 in the arsenal, and were some of the first weapons dismantled to comply with treaties limiting warhead numbers. The rationale for this decision was undoubtedly a combination of the lower yield and grave safety issues associated with the gun-type design.
For both the Trinity device and the Fat Man, the Nagasaki bomb, nearly identical plutonium fission through implosion designs were used. The Fat Man device specifically used 6.2 kg (14 lb), about 350 ml or 12 US fl oz in volume, of Pu-239, which is only 41% of bare-sphere critical mass. (See Fat Man article for a detailed drawing.) Surrounded by a U-238 reflector/tamper, the Fat Man's pit was brought close to critical mass by the neutron-reflecting properties of the U-238. During detonation, criticality was achieved by implosion. The plutonium pit was squeezed to increase its density by simultaneous detonation, as with the "Trinity" test detonation three weeks earlier, of the conventional explosives placed uniformly around the pit. The explosives were detonated by multiple exploding-bridgewire detonators. It is estimated that only about 20% of the plutonium underwent fission; the rest, about 5 kg (11 lb), was scattered.
An implosion shock wave might be of such short duration that only part of the pit is compressed at any instant as the wave passes through it. To prevent this, a pusher shell may be needed. The pusher is located between the explosive lens and the tamper. It works by reflecting some of the shock wave backwards, thereby having the effect of lengthening its duration. It is made out of a low density metal – such as aluminium, beryllium, or an alloy of the two metals (aluminium is easier and safer to shape, and is two orders of magnitude cheaper; beryllium has high-neutron-reflective capability). Fat Man used an aluminium pusher.
The series of RaLa Experiment tests of implosion-type fission weapon design concepts, carried out from July 1944 through February 1945 at the Los Alamos Laboratory and a remote site 14.3 km (9 miles) east of it in Bayo Canyon, proved the practicality of the implosion design for a fission device, with the February 1945 tests positively determining its usability for the final Trinity/Fat Man plutonium implosion design.
The key to Fat Man's greater efficiency was the inward momentum of the massive U-238 tamper. (The natural uranium tamper did not undergo fission from thermal neutrons, but did contribute perhaps 20% of the total yield from fission by fast neutrons). Once the chain reaction started in the plutonium, the momentum of the implosion had to be reversed before expansion could stop the fission. By holding everything together for a few hundred nanoseconds more, the efficiency was increased.
The core of an implosion weapon – the fissile material and any reflector or tamper bonded to it – is known as the pit. Some weapons tested during the 1950s used pits made with U-235 alone, or in composite with plutonium, but all-plutonium pits are the smallest in diameter and have been the standard since the early 1960s.
Casting and then machining plutonium is difficult not only because of its toxicity, but also because plutonium has many different metallic phases. As plutonium cools, changes in phase result in distortion and cracking. This distortion is normally overcome by alloying it with 30–35 mMol (0.9–1.0% by weight) gallium, forming a plutonium-gallium alloy, which causes it to take up its delta phase over a wide temperature range. When cooling from molten it then has only a single phase change, from epsilon to delta, instead of the four changes it would otherwise pass through. Other trivalent metals would also work, but gallium has a small neutron absorption cross section and helps protect the plutonium against corrosion. A drawback is that gallium compounds are corrosive and so if the plutonium is recovered from dismantled weapons for conversion to plutonium dioxide for power reactors, there is the difficulty of removing the gallium.
Because plutonium is chemically reactive it is common to plate the completed pit with a thin layer of inert metal, which also reduces the toxic hazard. The gadget used galvanic silver plating; afterwards, nickel deposited from nickel tetracarbonyl vapors was used, gold was preferred for many years. Recent designs improve safety by plating pits with vanadium to make the pits more fire-resistant.
The first improvement on the Fat Man design was to put an air space between the tamper and the pit to create a hammer-on-nail impact. The pit, supported on a hollow cone inside the tamper cavity, was said to be levitated. The three tests of Operation Sandstone, in 1948, used Fat Man designs with levitated pits. The largest yield was 49 kilotons, more than twice the yield of the unlevitated Fat Man.
It was immediately clear that implosion was the best design for a fission weapon. Its only drawback seemed to be its diameter. Fat Man was 1.5 metres (5 ft) wide vs 61 centimetres (2 ft) for Little Boy.
Eleven years later, implosion designs had advanced sufficiently that the 1.5-metre (5 ft)-diameter sphere of Fat Man had been reduced to a 0.3-metre (1 ft)-diameter cylinder 0.61 metres (2 ft) long, the Swan device.
The Pu-239 pit of Fat Man was only 9.1 centimetres (3.6 in) in diameter, the size of a softball. The bulk of Fat Man's girth was the implosion mechanism, namely concentric layers of U-238, aluminium, and high explosives. The key to reducing that girth was the two-point implosion design.
Two-point linear implosionEdit
In the two-point linear implosion, the nuclear fuel is cast into a solid shape and placed within the center of a cylinder of high explosive. Detonators are placed at either end of the explosive cylinder, and a plate-like insert, or shaper, is placed in the explosive just inside the detonators. When the detonators are fired, the initial detonation is trapped between the shaper and the end of the cylinder, causing it to travel out to the edges of the shaper where it is diffracted around the edges into the main mass of explosive. This causes the detonation to form into a ring that proceeds inwards from the shaper.
Due to the lack of a tamper or lenses to shape the progression, the detonation does not reach the pit in a spherical shape. To produce the desired spherical implosion, the fissile material itself is shaped to produce the same effect. Due to the physics of the shock wave propagation within the explosive mass, this requires the pit to be an oblong shape, roughly egg shaped. The shock wave first reaches the pit at its tips, driving them inward and causing the mass to become spherical. The shock may also change plutonium from delta to alpha phase, increasing its density by 23%, but without the inward momentum of a true implosion.
The lack of compression makes such designs inefficient, but the simplicity and small diameter make it suitable for use in artillery shells and atomic demolition munitions – ADMs – also known as backpack or suitcase nukes; an example is the W48 artillery shell, the smallest nuclear weapon ever built or deployed. All such low-yield battlefield weapons, whether gun-type U-235 designs or linear implosion Pu-239 designs, pay a high price in fissile material in order to achieve diameters between six and ten inches (15 and 25 cm).
List of US linear implosion weaponsEdit
Two-point hollow-pit implosionEdit
A more efficient two-point implosion system uses two high explosive lenses and a hollow pit.
A hollow plutonium pit was the original plan for the 1945 Fat Man bomb, but there was not enough time to develop and test the implosion system for it. A simpler solid-pit design was considered more reliable, given the time constraints, but it required a heavy U-238 tamper, a thick aluminium pusher, and three tons of high explosives.
After the war, interest in the hollow pit design was revived. Its obvious advantage is that a hollow shell of plutonium, shock-deformed and driven inward toward its empty center, would carry momentum into its violent assembly as a solid sphere. It would be self-tamping, requiring a smaller U-238 tamper, no aluminium pusher and less high explosive.
The Fat Man bomb had two concentric, spherical shells of high explosives, each about 25 cm (10 in) thick. The inner shell drove the implosion. The outer shell consisted of a soccer-ball pattern of 32 high explosive lenses, each of which converted the convex wave from its detonator into a concave wave matching the contour of the outer surface of the inner shell. If these 32 lenses could be replaced with only two, the high explosive sphere could become an ellipsoid (prolate spheroid) with a much smaller diameter.
A good illustration of these two features is a 1956 drawing from the Swedish nuclear weapons program (which was terminated before it produced a test explosion). The drawing shows the essential elements of the two-point hollow-pit design.
There are similar drawings in the open literature from the French program, which produced an arsenal.
The mechanism of the high explosive lens (diagram item #6) is not shown in the Swedish drawing, but a standard lens made of fast and slow high explosives, as in Fat Man, would be much longer than the shape depicted. For a single high explosive lens to generate a concave wave that envelops an entire hemisphere, it must either be very long or the part of the wave on a direct line from the detonator to the pit must be slowed dramatically.
A slow high explosive is too fast, but the flying plate of an "air lens" is not. A metal plate, shock-deformed and pushed across an empty space, can be designed to move slowly enough. A two-point implosion system using air lens technology can have a length no more than twice its diameter, as in the Swedish diagram above.
Fusion-boosted fission weaponsEdit
The next step in miniaturization was to speed up the fissioning of the pit to reduce the minimum inertial confinement time. This would allow the efficient fission of the fuel with less mass in the form of tamper or the fuel itself. The key to achieving faster fission would be to introduce more neutrons, and among the many ways to do this, adding a fusion reaction was relatively easy in the case of a hollow pit.
The easiest fusion reaction to achieve is found in a 50–50 mixture of tritium and deuterium. For fusion power experiments this mixture must be held at high temperatures for relatively lengthy times in order to have an efficient reaction. For explosive use, however, the goal is not to produce efficient fusion, but simply provide extra neutrons early in the process. Since a nuclear explosion is supercritical, any extra neutrons will be multiplied by the chain reaction, so even tiny quantities introduced early can have a large effect on the final outcome. For this reason, even the relatively low compression pressures and times (in fusion terms) found in the center of a hollow pit warhead are enough to create the desired effect.
In the boosted design, the fusion fuel in gas form is pumped into the pit during arming. This will fuse into helium and release free neutrons soon after fission begins. The neutrons will start a large number of new chain reactions while the pit is still critical or nearly critical. Once the hollow pit is perfected, there is little reason not to boost; deuterium and tritium are easily produced in the small quantities needed, and the technical aspects are trivial.
Boosting reduces diameter in three ways, all the result of faster fission:
- Since the compressed pit does not need to be held together as long, the massive U-238 tamper can be replaced by a light-weight beryllium shell (to reflect escaping neutrons back into the pit). The diameter is reduced.
- The mass of the pit can be reduced by half, without reducing yield. Diameter is reduced again.
- Since the mass of the metal being imploded (tamper plus pit) is reduced, a smaller charge of high explosive is needed, reducing diameter even further.
Since boosting is required to attain full design yield, any reduction in boosting reduces yield. Boosted weapons are thus variable-yield weapons (also known as dial-a-yield); yield can be reduced any time before detonation simply by reducing the amount of deuterium/tritium inserted into the pit during the arming procedure.
The first device whose dimensions suggest employment of all these features (two-point, hollow-pit, fusion-boosted implosion) was the Swan device. It had a cylindrical shape with a diameter of 11.6 in (29 cm) and a length of 22.8 in (58 cm).
It was first tested standalone and then as the primary of a two-stage thermonuclear device during Operation Redwing. It was weaponized as the Robin primary and became the first off-the-shelf, multi-use primary, and the prototype for all that followed.
After the success of Swan, 11 or 12 inches (28 or 30 cm) seemed to become the standard diameter of boosted single-stage devices tested during the 1950s. Length was usually twice the diameter, but one such device, which became the W54 warhead, was closer to a sphere, only 15 inches (38 cm) long. It was tested two dozen times in the 1957–62 period before being deployed. No other design had such a long string of test failures.
One of the applications of the W54 was the Davy Crockett XM-388 recoilless rifle projectile. It had a dimension of just 11 inches (28 cm), and is shown here in comparison to its Fat Man predecessor (60 inches (150 cm)).
Another benefit of boosting, in addition to making weapons smaller, lighter, and with less fissile material for a given yield, is that it renders weapons immune to radiation interference (RI). It was discovered in the mid-1950s that plutonium pits would be particularly susceptible to partial predetonation if exposed to the intense radiation of a nearby nuclear explosion (electronics might also be damaged, but this was a separate problem). RI was a particular problem before effective early warning radar systems because a first strike attack might make retaliatory weapons useless. Boosting reduces the amount of plutonium needed in a weapon to below the quantity which would be vulnerable to this effect.
Two-stage thermonuclear weaponsEdit
Pure fission or fusion-boosted fission weapons can be made to yield hundreds of kilotons, at great expense in fissile material and tritium, but by far the most efficient way to increase nuclear weapon yield beyond ten or so kilotons is to add a second independent stage, called a secondary.
In the 1940s, bomb designers at Los Alamos thought the secondary would be a canister of deuterium in liquefied or hydride form. The fusion reaction would be D-D, harder to achieve than D-T, but more affordable. A fission bomb at one end would shock-compress and heat the near end, and fusion would propagate through the canister to the far end. Mathematical simulations showed it would not work, even with large amounts of expensive tritium added.
The entire fusion fuel canister would need to be enveloped by fission energy, to both compress and heat it, as with the booster charge in a boosted primary. The design breakthrough came in January 1951, when Edward Teller and Stanislaw Ulam invented radiation implosion – for nearly three decades known publicly only as the Teller-Ulam H-bomb secret.
The concept of radiation implosion was first tested on May 9, 1951, in the George shot of Operation Greenhouse, Eniwetok, yield 225 kilotons. The first full test was on November 1, 1952, the Mike shot of Operation Ivy, Eniwetok, yield 10.4 megatons.
In radiation implosion, the burst of X-ray energy coming from an exploding primary is captured and contained within an opaque-walled radiation channel which surrounds the nuclear energy components of the secondary. The radiation quickly turns the plastic foam that had been filling the channel into a plasma which is mostly transparent to X-rays, and the radiation is absorbed in the outermost layers of the pusher/tamper surrounding the secondary, which ablates and applies a massive force (much like an inside out rocket engine) causing the fusion fuel capsule to implode much like the pit of the primary. As the secondary implodes a fissile "spark plug" at its center ignites and provides neutrons and heat which enable the lithium deuteride fusion fuel to produce tritium and ignite as well. The fission and fusion chain reactions exchange neutrons with each other and boost the efficiency of both reactions. The greater implosive force, enhanced efficiency of the fissile "spark plug" due to boosting via fusion neutrons, and the fusion explosion itself provide significantly greater explosive yield from the secondary despite often not being much larger than the primary.
For example, for the Redwing Mohawk test on July 3, 1956, a secondary called the Flute was attached to the Swan primary. The Flute was 15 inches (38 cm) in diameter and 23.4 inches (59 cm) long, about the size of the Swan. But it weighed ten times as much and yielded 24 times as much energy (355 kilotons, vs 15 kilotons).
Equally important, the active ingredients in the Flute probably cost no more than those in the Swan. Most of the fission came from cheap U-238, and the tritium was manufactured in place during the explosion. Only the spark plug at the axis of the secondary needed to be fissile.
A spherical secondary can achieve higher implosion densities than a cylindrical secondary, because spherical implosion pushes in from all directions toward the same spot. However, in warheads yielding more than one megaton, the diameter of a spherical secondary would be too large for most applications. A cylindrical secondary is necessary in such cases. The small, cone-shaped re-entry vehicles in multiple-warhead ballistic missiles after 1970 tended to have warheads with spherical secondaries, and yields of a few hundred kilotons.
As with boosting, the advantages of the two-stage thermonuclear design are so great that there is little incentive not to use it, once a nation has mastered the technology.
In engineering terms, radiation implosion allows for the exploitation of several known features of nuclear bomb materials which heretofore had eluded practical application. For example:
- The optimal way to store deuterium in a reasonably dense state is to chemically bond it with lithium, as lithium deuteride. But the lithium-6 isotope is also the raw material for tritium production, and an exploding bomb is a nuclear reactor. Radiation implosion will hold everything together long enough to permit the complete conversion of lithium-6 into tritium, while the bomb explodes. So the bonding agent for deuterium permits use of the D-T fusion reaction without any pre-manufactured tritium being stored in the secondary. The tritium production constraint disappears.
- For the secondary to be imploded by the hot, radiation-induced plasma surrounding it, it must remain cool for the first microsecond, i.e., it must be encased in a massive radiation (heat) shield. The shield's massiveness allows it to double as a tamper, adding momentum and duration to the implosion. No material is better suited for both of these jobs than ordinary, cheap uranium-238, which also happens to undergo fission when struck by the neutrons produced by D-T fusion. This casing, called the pusher, thus has three jobs: to keep the secondary cool; to hold it, inertially, in a highly compressed state; and, finally, to serve as the chief energy source for the entire bomb. The consumable pusher makes the bomb more a uranium fission bomb than a hydrogen fusion bomb. Insiders never used the term "hydrogen bomb".
- Finally, the heat for fusion ignition comes not from the primary but from a second fission bomb called the spark plug, embedded in the heart of the secondary. The implosion of the secondary implodes this spark plug, detonating it and igniting fusion in the material around it, but the spark plug then continues to fission in the neutron-rich environment until it is fully consumed, adding significantly to the yield.
The initial impetus behind the two-stage weapon was President Truman's 1950 promise to build a 10-megaton hydrogen superbomb as the U.S. response to the 1949 test of the first Soviet fission bomb. But the resulting invention turned out to be the cheapest and most compact way to build small nuclear bombs as well as large ones, erasing any meaningful distinction between A-bombs and H-bombs, and between boosters and supers. All preferred techniques for fission and fusion explosions are incorporated into one all-encompassing, fully scalable design principle. Even 6-inch (150 mm) diameter nuclear artillery shells can be two-stage thermonuclears.
In the ensuing fifty years, nobody has come up with a more efficient way to build a nuclear bomb. It is the design of choice for the United States, Russia, the United Kingdom, China, and France, the five thermonuclear powers. On 3 September 2017 North Korea carried out what it reported as its first "two-stage thermo-nuclear weapon" test. According to Dr. Theodore Taylor, after reviewing leaked photographs of disassembled weapons components taken before 1986, Israel possessed boosted weapons and would require supercomputers of that era to advance further toward full two-stage weapons in the megaton range without nuclear test detonations. The other nuclear-armed nations, India and Pakistan, probably have single-stage weapons, possibly boosted.
In a two-stage thermonuclear weapon the energy from the primary impacts the secondary. An essential energy transfer modulator called the interstage, between the primary and the secondary, protects the secondary's fusion fuel from heating too quickly, which could cause it to explode in a conventional (and small) heat explosion before the fusion and fission reactions get a chance to start.
There is very little information in the open literature about the mechanism of the interstage. Its first mention in a U.S. government document formally released to the public appears to be a caption in a graphic promoting the Reliable Replacement Warhead Program in 2007. If built, this new design would replace "toxic, brittle material" and "expensive 'special' material" in the interstage. This statement suggests the interstage may contain beryllium to moderate the flux of neutrons from the primary, and perhaps something to absorb and re-radiate the x-rays in a particular manner. There is also some speculation that this interstage material, which may be code-named FOGBANK, might be an aerogel, possibly doped with beryllium and/or other substances.
The interstage and the secondary are encased together inside a stainless steel membrane to form the canned subassembly (CSA), an arrangement which has never been depicted in any open-source drawing. The most detailed illustration of an interstage shows a British thermonuclear weapon with a cluster of items between its primary and a cylindrical secondary. They are labeled "end-cap and neutron focus lens", "reflector/neutron gun carriage", and "reflector wrap". The origin of the drawing, posted on the internet by Greenpeace, is uncertain, and there is no accompanying explanation.
While every nuclear weapon design falls into one of the above categories, specific designs have occasionally become the subject of news accounts and public discussion, often with incorrect descriptions about how they work and what they do. Examples:
While all modern nuclear weapons (fission and fusion alike) make some use of D-T fusion, in the public perception hydrogen bombs are multi-megaton devices a thousand times more powerful than Hiroshima's Little Boy. Such high-yield bombs are actually two-stage thermonuclears, scaled up to the desired yield, with uranium fission, as usual, providing most of their energy.
The idea of the hydrogen bomb first came to public attention in 1949, when prominent scientists openly recommended against building nuclear bombs more powerful than the standard pure-fission model, on both moral and practical grounds. Their assumption was that critical mass considerations would limit the potential size of fission explosions, but that a fusion explosion could be as large as its supply of fuel, which has no critical mass limit. In 1949, the Soviets exploded their first fission bomb, and in 1950 U.S. President Harry S. Truman ended the H-bomb debate by ordering the Los Alamos designers to build one.
In 1952, the 10.4-megaton Ivy Mike explosion was announced as the first hydrogen bomb test, reinforcing the idea that hydrogen bombs are a thousand times more powerful than fission bombs.
In 1954, J. Robert Oppenheimer was labeled a hydrogen bomb opponent. The public did not know there were two kinds of hydrogen bomb (neither of which is accurately described as a hydrogen bomb). On May 23, when his security clearance was revoked, item three of the four public findings against him was "his conduct in the hydrogen bomb program." In 1949, Oppenheimer had supported single-stage fusion-boosted fission bombs, to maximize the explosive power of the arsenal given the trade-off between plutonium and tritium production. He opposed two-stage thermonuclear bombs until 1951, when radiation implosion, which he called "technically sweet", first made them practical. The complexity of his position was not revealed to the public until 1976, nine years after his death.
When ballistic missiles replaced bombers in the 1960s, most multi-megaton bombs were replaced by missile warheads (also two-stage thermonuclears) scaled down to one megaton or less.
The first effort to exploit the symbiotic relationship between fission and fusion was a 1940s design that mixed fission and fusion fuel in alternating thin layers. As a single-stage device, it would have been a cumbersome application of boosted fission. It first became practical when incorporated into the secondary of a two-stage thermonuclear weapon.
The U.S. name, Alarm Clock, came from Teller: he called it that because it might "wake up the world" to the possibility of the potential of the Super. The Russian name for the same design was more descriptive: Sloika (Russian: Слойка), a layered pastry cake. A single-stage Soviet Sloika was tested on August 12, 1953. No single-stage U.S. version was tested, but the Union shot of Operation Castle, April 26, 1954, was a two-stage thermonuclear device code-named Alarm Clock. Its yield, at Bikini, was 6.9 megatons.
Because the Soviet Sloika test used dry lithium-6 deuteride eight months before the first U.S. test to use it (Castle Bravo, March 1, 1954), it was sometimes claimed that the USSR won the H-bomb race, even though the United States tested and developed the first hydrogen bomb: the Ivy Mike H-bomb test. The 1952 U.S. Ivy Mike test used cryogenically cooled liquid deuterium as the fusion fuel in the secondary, and employed the D-D fusion reaction. However, the first Soviet test to use a radiation-imploded secondary, the essential feature of a true H-bomb, was on November 23, 1955, three years after Ivy Mike. In fact, real work on the implosion scheme in the Soviet Union only commenced in the very early part of 1953, several months after the successful testing of Sloika.
On March 1, 1954, the largest-ever U.S. nuclear test explosion, the 15-megaton Bravo shot of Operation Castle at Bikini Atoll, delivered a promptly lethal dose of fission-product fallout to more than 6,000 square miles (16,000 km2) of Pacific Ocean surface. Radiation injuries to Marshall Islanders and Japanese fishermen made that fact public and revealed the role of fission in hydrogen bombs.
In response to the public alarm over fallout, an effort was made to design a clean multi-megaton weapon, relying almost entirely on fusion. The energy produced by the fissioning of unenriched natural uranium, when used as the tamper material in the secondary and subsequent stages in the Teller-Ulam design, can far exceed the energy released by fusion, as was the case in the Castle Bravo test. Replacing the fissionable material in the tamper with another material is essential to producing a "clean" bomb. In such a device, the tamper no longer contributes energy, so for any given weight, a clean bomb will have less yield. The earliest known incidence of a three-stage device being tested, with the third stage, called the tertiary, being ignited by the secondary, was May 27, 1956 in the Bassoon device. This device was tested in the Zuni shot of Operation Redwing. This shot used non-fissionable tampers; an inert substitute material such as tungsten or lead was used. Its yield was 3.5 megatons, 85% fusion and only 15% fission.
The public records for devices that produced the highest proportion of their yield via fusion reactions are the peaceful nuclear explosions of the 1970s, with the 3 detonations that excavated part of Pechora–Kama Canal being cited as 98% fusion each in the Taiga test's 15 kiloton explosive yield devices; that is, a total fission fraction of 0.3 kilotons in a 15 kt device. Others include the 50 megaton Tsar Bomba at 97% fusion, the 9.3 megaton Hardtack Poplar test at 95%, and the 4.5 megaton Redwing Navajo test at 95% fusion.
On July 19, 1956, AEC Chairman Lewis Strauss said that the Redwing Zuni shot clean bomb test "produced much of importance ... from a humanitarian aspect." However, less than two days after this announcement, the dirty version of Bassoon, called Bassoon Prime, with a uranium-238 tamper in place, was tested on a barge off the coast of Bikini Atoll as the Redwing Tewa shot. The Bassoon Prime produced a 5-megaton yield, of which 87% came from fission. Data obtained from this test, and others, culminated in the eventual deployment of the highest yielding US nuclear weapon known, and the highest yield-to-weight weapon ever made, a three-stage thermonuclear weapon with a maximum "dirty" yield of 25 megatons, designated as the B41 nuclear bomb, which was to be carried by U.S. Air Force bombers until it was decommissioned; this weapon was never fully tested.
As such, high-yield clean bombs appear to have been of little value from a military standpoint. The actual deployed weapons were the dirty versions, which maximized yield for the same size device. The need for low fission fraction nuclear devices was driven only by the likes of Project Orion and peaceful nuclear explosions – for earth excavation with little contamination of the resulting excavated area.
Third generation nuclear weaponsEdit
First and second generation nuclear weapons release energy as omnidirectional blasts. Third generation nuclear weapons are experimental special effect warheads and devices that can release energy in a directed manner, some of which were tested during the Cold War but were never deployed. These include:
- Project Prometheus, also known as "Nuclear Shotgun", which would have used a nuclear explosion to accelerate kinetic penetrators against ICBMs.
- Project Excalibur, a nuclear-pumped X-ray laser
Fourth generation nuclear weaponsEdit
Newer 4th-generation nuclear weapons designs including pure fusion weapons and antimatter-catalyzed nuclear pulse propulsion-like devices, are being studied by the five largest nuclear weapon states.
Nanotechnology can theoretically produce miniaturised laser-triggered pure fusion weapons that will be easier to produce than conventional nuclear weapons.
A doomsday bomb, made popular by Nevil Shute's 1957 novel, and subsequent 1959 movie, On the Beach, the cobalt bomb is a hydrogen bomb with a jacket of cobalt. The neutron-activated cobalt would have maximized the environmental damage from radioactive fallout. These bombs were popularized in the 1964 film Dr. Strangelove or: How I Learned to Stop Worrying and Love the Bomb; the material added to the bombs is referred to in the film as 'cobalt-thorium G'.
Such "salted" weapons were requested by the U.S. Air Force and seriously investigated, possibly built and tested, but not deployed. In the 1964 edition of the DOD/AEC book The Effects of Nuclear Weapons, a new section titled Radiological Warfare clarified the issue. Fission products are as deadly as neutron-activated cobalt. The standard high-fission thermonuclear weapon is automatically a weapon of radiological warfare, as dirty as a cobalt bomb.
Initially, gamma radiation from the fission products of an equivalent size fission-fusion-fission bomb are much more intense than Co-60: 15,000 times more intense at 1 hour; 35 times more intense at 1 week; 5 times more intense at 1 month; and about equal at 6 months. Thereafter fission drops off rapidly so that Co-60 fallout is 8 times more intense than fission at 1 year and 150 times more intense at 5 years. The very long-lived isotopes produced by fission would overtake the 60Co again after about 75 years.
The triple "taiga" nuclear salvo test, as part of the preliminary March 1971 Pechora–Kama Canal project, produced a small amount of fission products and therefore a comparatively large amount of case material activated products are responsible for most of the residual activity at the site today, namely Co-60. With this fusion generated neutron activation product being responsible for about half of the gamma dose now(2011) at the test site, albeit with that dose being too small to cause deleterious effects, normal green vegetation exists all around the lake that was formed.
Fission-fusion-fission bombs vs. three-stage (tertiary) bombsEdit
This article may contain too much repetition or redundant language.July 2015) (Learn how and when to remove this template message)(
In 1954, to explain the surprising amount of fission-product fallout produced by hydrogen bombs, Ralph Lapp coined the term fission-fusion-fission to describe a process inside what he called a three-stage thermonuclear weapon. His process explanation was correct, but his choice of terms caused confusion in the open literature. The stages of a nuclear weapon are not fission, fusion, and fission. They are the primary, the secondary, and, in a very few exceptional and powerful weapons no longer in service, the tertiary. Tertiary (three-stage) designs, such as the U.S. B41 nuclear bomb and the Soviet Tsar Bomba (discussed above), were developed in the late 1950s and early 1960s; all have since been retired, as the typical multi-megaton yields of tertiary bombs do not destroy targets efficiently, since they waste energy in a sphere above and below an area of land. For this reason, all tertiary bombs have given way in modern nuclear arsenals to multiple smaller two-stage bomb tactics (see for example, MIRV). Such two-stage bombs, even though less efficient in yield, are nevertheless more destructive for their total bomb weight, because they can be distributed over a roughly two-dimensional area of land at the target.
All so-called "fission-fusion-fission" weapons (i.e., all conventional modern thermonuclear warheads) employ the additional step of "jacket fissioning", using fusion neutrons. This works as follows: the high-energy or "fast" neutrons generated by fusion are used to fission a fissionable jacket located around the fusion stage. In the past this jacket was often made of natural or depleted uranium; but today's weapons in which there is a premium on weight and size (i.e., virtually all modern strategic weapons) use moderately-to-highly enriched uranium as the jacketing material (see Oralloy thermonuclear warheads section below). The fast fission of the secondary jacket in fission-fusion-fission bombs is sometimes referred to as a "third stage" in the bomb, but it should not be confused with the obsolete true three-stage thermonuclear design, in which there existed another complete tertiary fusion stage.
In the era of open-air atomic testing, the fission jacket was sometimes omitted, in order to create so-called "clean bombs" (see above), or to reduce the amount of radioactive fallout from fission products in very large multi-megaton blasts. This was done most often in the testing of very large tertiary bomb designs, such as the Tsar Bomba and the Zuni test shot of Operation Redwing, as discussed above. In the testing of such weapons, it was assumed (and sometimes shown operationally) that a jacket of natural uranium or enriched uranium could always be added to a given unjacketed bomb, if desired, to increase the yield from two to five times.
Arbitrarily large multi-staged devicesEdit
The idea of a device which has an arbitrarily large number of Teller-Ulam stages, with each driving a larger radiation-driven implosion than the preceding stage, is frequently suggested, but technically disputed. There are "well-known sketches and some reasonable-looking calculations in the open literature about two-stage weapons, but no similarly accurate descriptions of true three stage concepts."
According to George Lemmer's 1967 Air Force and Strategic Deterrence 1951–1960 paper, in 1957, LANL stated that a 1,000-megaton warhead could be built. Apparently there were three of these US designs analyzed in the gigaton (1,000-megaton) range; LLNL's GNOMON and SUNDIAL – objects that cast shadows – and LANL's "TAV". SUNDIAL attempting to have a 10 Gt yield, while the Gnomon and TAV designs attempted to produce a yield of 1 Gt.[better source needed] A freedom of information request was filed (FOIA 13-00049-K) for information on the three above US designs. The request was denied under statutory exemptions relating to classified material; the denial was appealed, but the request was finally denied again in April 2016.
Following the concern caused by the estimated gigaton scale of the 1994 Comet Shoemaker-Levy 9 impacts on the planet Jupiter, in a 1995 meeting at Lawrence Livermore National Laboratory (LLNL), Edward Teller proposed to a collective of U.S. and Russian ex-Cold War weapons designers that they collaborate on designing a 1000-megaton nuclear explosive device for diverting extinction-class asteroids (10+ km in diameter), which would be employed in the event that one of these asteroids were on an impact trajectory with Earth.
There have also been some calculations made in 1979 by Lowell Wood, Teller's protégé, that Teller's initially-unworkable "classical Super" design, analogous to igniting a candlestick of deuterium fuel, could potentially achieve ignition reliably were it touched off by a sufficiently-large Teller-Ulam device, rather than the gun-type fission weapon used in the original design.
A neutron bomb, technically referred to as an enhanced radiation weapon (ERW), is a type of tactical nuclear weapon designed specifically to release a large portion of its energy as energetic neutron radiation. This contrasts with standard thermonuclear weapons, which are designed to capture this intense neutron radiation to increase its overall explosive yield. In terms of yield, ERWs typically produce about one-tenth that of a fission-type atomic weapon. Even with their significantly lower explosive power, ERWs are still capable of much greater destruction than any conventional bomb. Meanwhile, relative to other nuclear weapons, damage is more focused on biological material than on material infrastructure (though extreme blast and heat effects are not eliminated).
ERWs are more accurately described as suppressed yield weapons. When the yield of a nuclear weapon is less than one kiloton, its lethal radius from blast, 700 m (2,300 ft), is less than that from its neutron radiation. However, the blast is more than potent enough to destroy most structures, which are less resistant to blast effects than even unprotected human beings. Blast pressures of upwards of 20 PSI are survivable, whereas most buildings will collapse with a pressure of only 5 PSI.
Commonly misconceived as a weapon designed to kill populations and leave infrastructure intact, these bombs (as mentioned above) are still very capable of leveling buildings over a large radius. The intent of their design was to kill tank crews – tanks giving excellent protection against blast and heat, surviving (relatively) very close to a detonation. Given the Soviets' vast tank forces during the Cold War, this was the perfect weapon to counter them. The neutron radiation could instantly incapacitate a tank crew out to roughly the same distance that the heat and blast would incapacitate an unprotected human (depending on design). The tank chassis would also be rendered highly radioactive, temporarily preventing its re-use by a fresh crew.
Neutron weapons were also intended for use in other applications, however. For example, they are effective in anti-nuclear defenses – the neutron flux being capable of neutralising an incoming warhead at a greater range than heat or blast. Nuclear warheads are very resistant to physical damage, but are very difficult to harden against extreme neutron flux.
ERWs were two-stage thermonuclears with all non-essential uranium removed to minimize fission yield. Fusion provided the neutrons. Developed in the 1950s, they were first deployed in the 1970s, by U.S. forces in Europe. The last ones were retired in the 1990s.
A neutron bomb is only feasible if the yield is sufficiently high that efficient fusion stage ignition is possible, and if the yield is low enough that the case thickness will not absorb too many neutrons. This means that neutron bombs have a yield range of 1–10 kilotons, with fission proportion varying from 50% at 1-kiloton to 25% at 10-kilotons (all of which comes from the primary stage). The neutron output per kiloton is then 10–15 times greater than for a pure fission implosion weapon or for a strategic warhead like a W87 or W88.
Oralloy thermonuclear warheadsEdit
In 1999, nuclear weapon design was in the news again, for the first time in decades. In January, the U.S. House of Representatives released the Cox Report (Christopher Cox R-CA) which alleged that China had somehow acquired classified information about the U.S. W88 warhead. Nine months later, Wen Ho Lee, a Taiwanese immigrant working at Los Alamos, was publicly accused of spying, arrested, and served nine months in pre-trial detention, before the case against him was dismissed. It is not clear that there was, in fact, any espionage.
In the course of eighteen months of news coverage, the W88 warhead was described in unusual detail. The New York Times printed a schematic diagram on its front page. The most detailed drawing appeared in A Convenient Spy, the 2001 book on the Wen Ho Lee case by Dan Stober and Ian Hoffman, adapted and shown here with permission.
Designed for use on Trident II (D-5) submarine-launched ballistic missiles, the W88 entered service in 1990 and was the last warhead designed for the U.S. arsenal. It has been described as the most advanced, although open literature accounts do not indicate any major design features that were not available to U.S. designers in 1958.
The above diagram shows all the standard features of ballistic missile warheads since the 1960s, with two exceptions that give it a higher yield for its size.
- The outer layer of the secondary, called the "pusher", which serves three functions: heat shield, tamper, and fission fuel, is made of U-235 instead of U-238, hence the name Oralloy (U-235) Thermonuclear. Being fissile, rather than merely fissionable, allows the pusher to fission faster and more completely, increasing yield. This feature is available only to nations with a great wealth of fissile uranium. The United States is estimated to have 500 tons.
- The secondary is located in the wide end of the re-entry cone, where it can be larger, and thus more powerful. The usual arrangement is to put the heavier, denser secondary in the narrow end for greater aerodynamic stability during re-entry from outer space, and to allow more room for a bulky primary in the wider part of the cone. (The W87 warhead drawing in the W87 article shows the usual arrangement.) Because of this new geometry, the W88 primary uses compact conventional high explosives (CHE) to save space, rather than the more usual, and bulky but safer, insensitive high explosives (IHE). The re-entry cone probably has ballast in the nose for aerodynamic stability.
The alternating layers of fission and fusion material in the secondary are an application of the Alarm Clock/Sloika principle.
Reliable replacement warheadEdit
The United States has not produced any nuclear warheads since 1989, when the Rocky Flats pit production plant, near Boulder, Colorado, was shut down for environmental reasons. With the end of the Cold War two years later, the production line was idled except for inspection and maintenance functions.
The National Nuclear Security Administration, the latest successor for nuclear weapons to the Atomic Energy Commission and the Department of Energy, has proposed building a new pit facility and starting the production line for a new warhead called the Reliable Replacement Warhead (RRW). Two advertised safety improvements of the RRW would be a return to the use of "insensitive high explosives which are far less susceptible to accidental detonation", and the elimination of "certain hazardous materials, such as beryllium, that are harmful to people and the environment." Because of the U.S. moratorium on nuclear explosive testing, any new design would rely on previously tested concepts.
Weapon design laboratoriesEdit
The examples and perspective in this section deal primarily with the United States and do not represent a worldwide view of the subject. (June 2014) (Learn how and when to remove this template message)
All the nuclear weapon design innovations discussed in this article originated from the following three labs in the manner described. Other nuclear weapon design labs in other countries duplicated those design innovations independently, reverse-engineered them from fallout analysis, or acquired them by espionage.
The first systematic exploration of nuclear weapon design concepts took place in mid-1942 at the University of California, Berkeley. Important early discoveries had been made at the adjacent Lawrence Berkeley Laboratory, such as the 1940 cyclotron-made production and isolation of plutonium. A Berkeley professor, J. Robert Oppenheimer, had just been hired to run the nation's secret bomb design effort. His first act was to convene the 1942 summer conference.
By the time he moved his operation to the new secret town of Los Alamos, New Mexico, in the spring of 1943, the accumulated wisdom on nuclear weapon design consisted of five lectures by Berkeley professor Robert Serber, transcribed and distributed as the Los Alamos Primer. The Primer addressed fission energy, neutron production and capture, nuclear chain reactions, critical mass, tampers, predetonation, and three methods of assembling a bomb: gun assembly, implosion, and "autocatalytic methods", the one approach that turned out to be a dead end.
At Los Alamos, it was found in April 1944 by Emilio Segrè that the proposed Thin Man Gun assembly type bomb would not work for plutonium because of predetonation problems caused by Pu-240 impurities. So Fat Man, the implosion-type bomb, was given high priority as the only option for plutonium. The Berkeley discussions had generated theoretical estimates of critical mass, but nothing precise. The main wartime job at Los Alamos was the experimental determination of critical mass, which had to wait until sufficient amounts of fissile material arrived from the production plants: uranium from Oak Ridge, Tennessee, and plutonium from the Hanford Site in Washington.
In 1945, using the results of critical mass experiments, Los Alamos technicians fabricated and assembled components for four bombs: the Trinity Gadget, Little Boy, Fat Man, and an unused spare Fat Man. After the war, those who could, including Oppenheimer, returned to university teaching positions. Those who remained worked on levitated and hollow pits and conducted weapon effects tests such as Crossroads Able and Baker at Bikini Atoll in 1946.
All of the essential ideas for incorporating fusion into nuclear weapons originated at Los Alamos between 1946 and 1952. After the Teller-Ulam radiation implosion breakthrough of 1951, the technical implications and possibilities were fully explored, but ideas not directly relevant to making the largest possible bombs for long-range Air Force bombers were shelved.
Because of Oppenheimer's initial position in the H-bomb debate, in opposition to large thermonuclear weapons, and the assumption that he still had influence over Los Alamos despite his departure, political allies of Edward Teller decided he needed his own laboratory in order to pursue H-bombs. By the time it was opened in 1952, in Livermore, California, Los Alamos had finished the job Livermore was designed to do.
With its original mission no longer available, the Livermore lab tried radical new designs that failed. Its first three nuclear tests were fizzles: in 1953, two single-stage fission devices with uranium hydride pits, and in 1954, a two-stage thermonuclear device in which the secondary heated up prematurely, too fast for radiation implosion to work properly.
Shifting gears, Livermore settled for taking ideas Los Alamos had shelved and developing them for the Army and Navy. This led Livermore to specialize in small-diameter tactical weapons, particularly ones using two-point implosion systems, such as the Swan. Small-diameter tactical weapons became primaries for small-diameter secondaries. Around 1960, when the superpower arms race became a ballistic missile race, Livermore warheads were more useful than the large, heavy Los Alamos warheads. Los Alamos warheads were used on the first intermediate-range ballistic missiles, IRBMs, but smaller Livermore warheads were used on the first intercontinental ballistic missiles, ICBMs, and submarine-launched ballistic missiles, SLBMs, as well as on the first multiple warhead systems on such missiles.
In 1957 and 1958, both labs built and tested as many designs as possible, in anticipation that a planned 1958 test ban might become permanent. By the time testing resumed in 1961 the two labs had become duplicates of each other, and design jobs were assigned more on workload considerations than lab specialty. Some designs were horse-traded. For example, the W38 warhead for the Titan I missile started out as a Livermore project, was given to Los Alamos when it became the Atlas missile warhead, and in 1959 was given back to Livermore, in trade for the W54 Davy Crockett warhead, which went from Livermore to Los Alamos.
Warhead designs after 1960 took on the character of model changes, with every new missile getting a new warhead for marketing reasons. The chief substantive change involved packing more fissile uranium-235 into the secondary, as it became available with continued uranium enrichment and the dismantlement of the large high-yield bombs.
Starting with the Nova facility at Livermore in the mid-1980s, nuclear design activity pertaining to radiation-driven implosion was informed by research with indirect drive laser fusion. This work was part of the effort to investigate Inertial Confinement Fusion. Similar work continues at the more powerful National Ignition Facility. The Stockpile Stewardship and Management Program also benefitted from research performed at NIF.
Nuclear weapons are in large part designed by trial and error. The trial often involves test explosion of a prototype.
In a nuclear explosion, a large number of discrete events, with various probabilities, aggregate into short-lived, chaotic energy flows inside the device casing. Complex mathematical models are required to approximate the processes, and in the 1950s there were no computers powerful enough to run them properly. Even today's computers and simulation software are not adequate.
It was easy enough to design reliable weapons for the stockpile. If the prototype worked, it could be weaponized and mass-produced.
It was much more difficult to understand how it worked or why it failed. Designers gathered as much data as possible during the explosion, before the device destroyed itself, and used the data to calibrate their models, often by inserting fudge factors into equations to make the simulations match experimental results. They also analyzed the weapon debris in fallout to see how much of a potential nuclear reaction had taken place.
An important tool for test analysis was the diagnostic light pipe. A probe inside a test device could transmit information by heating a plate of metal to incandescence, an event that could be recorded by instruments located at the far end of a long, very straight pipe.
The picture below shows the Shrimp device, detonated on March 1, 1954 at Bikini, as the Castle Bravo test. Its 15-megaton explosion was the largest ever by the United States. The silhouette of a man is shown for scale. The device is supported from below, at the ends. The pipes going into the shot cab ceiling, which appear to be supports, are actually diagnostic light pipes. The eight pipes at the right end (1) sent information about the detonation of the primary. Two in the middle (2) marked the time when X-rays from the primary reached the radiation channel around the secondary. The last two pipes (3) noted the time radiation reached the far end of the radiation channel, the difference between (2) and (3) being the radiation transit time for the channel.
From the shot cab, the pipes turned horizontally and traveled 7500 ft (2.3 km) along a causeway built on the Bikini reef to a remote-controlled data collection bunker on Namu Island.
While x-rays would normally travel at the speed of light through a low-density material like the plastic foam channel filler between (2) and (3), the intensity of radiation from the exploding primary creates a relatively opaque radiation front in the channel filler, which acts like a slow-moving logjam to retard the passage of radiant energy. While the secondary is being compressed via radiation-induced ablation, neutrons from the primary catch up with the x-rays, penetrate into the secondary, and start breeding tritium via the third reaction noted in the first section above. This Li-6 + n reaction is exothermic, producing 5 MeV per event. The spark plug has not yet been compressed, and, thus, remains subcritical, so no significant fission or fusion takes place as a result. If enough neutrons arrive before implosion of the secondary is complete, though, the crucial temperature differential between the outer and inner parts of the secondary can be degraded, potentially causing the secondary to fail to ignite. The first Livermore-designed thermonuclear weapon, the Morgenstern device, failed in this manner when it was tested as Castle Koon on April 7, 1954. The primary ignited, but the secondary, preheated by the primary's neutron wave, suffered what was termed as an inefficient detonation;:165 thus, a weapon with a predicted one-megaton yield produced only 110 kilotons, of which merely 10 kt were attributed to fusion.:316
These timing effects, and any problems they cause, are measured by light-pipe data. The mathematical simulations which they calibrate are called radiation flow hydrodynamics codes, or channel codes. They are used to predict the effect of future design modifications.
It is not clear from the public record how successful the Shrimp light pipes were. The unmanned data bunker was far enough back to remain outside the mile-wide crater, but the 15-megaton blast, two and a half times as powerful as expected, breached the bunker by blowing its 20-ton door off the hinges and across the inside of the bunker. (The nearest people were twenty miles (32 km) farther away, in a bunker that survived intact.)
The most interesting data from Castle Bravo came from radio-chemical analysis of weapon debris in fallout. Because of a shortage of enriched lithium-6, 60% of the lithium in the Shrimp secondary was ordinary lithium-7, which doesn't breed tritium as easily as lithium-6 does. But it does breed lithium-6 as the product of an (n, 2n) reaction (one neutron in, two neutrons out), a known fact, but with unknown probability. The probability turned out to be high.
Fallout analysis revealed to designers that, with the (n, 2n) reaction, the Shrimp secondary effectively had two and half times as much lithium-6 as expected. The tritium, the fusion yield, the neutrons, and the fission yield were all increased accordingly.
As noted above, Bravo's fallout analysis also told the outside world, for the first time, that thermonuclear bombs are more fission devices than fusion devices. A Japanese fishing boat, Daigo Fukuryū Maru, sailed home with enough fallout on her decks to allow scientists in Japan and elsewhere to determine, and announce, that most of the fallout had come from the fission of U-238 by fusion-produced 14 MeV neutrons.
The global alarm over radioactive fallout, which began with the Castle Bravo event, eventually drove nuclear testing literally underground. The last U.S. above-ground test took place at Johnston Island on November 4, 1962. During the next three decades, until September 23, 1992, the United States conducted an average of 2.4 underground nuclear explosions per month, all but a few at the Nevada Test Site (NTS) northwest of Las Vegas.
The Yucca Flat section of the NTS is covered with subsidence craters resulting from the collapse of terrain over radioactive caverns created by nuclear explosions (see photo).
After the 1974 Threshold Test Ban Treaty (TTBT), which limited underground explosions to 150 kilotons or less, warheads like the half-megaton W88 had to be tested at less than full yield. Since the primary must be detonated at full yield in order to generate data about the implosion of the secondary, the reduction in yield had to come from the secondary. Replacing much of the lithium-6 deuteride fusion fuel with lithium-7 hydride limited the tritium available for fusion, and thus the overall yield, without changing the dynamics of the implosion. The functioning of the device could be evaluated using light pipes, other sensing devices, and analysis of trapped weapon debris. The full yield of the stockpiled weapon could be calculated by extrapolation.
The examples and perspective in this section deal primarily with the United States and do not represent a worldwide view of the subject. (June 2014) (Learn how and when to remove this template message)
When two-stage weapons became standard in the early 1950s, weapon design determined the layout of the new, widely dispersed U.S. production facilities, and vice versa.
Because primaries tend to be bulky, especially in diameter, plutonium is the fissile material of choice for pits, with beryllium reflectors. It has a smaller critical mass than uranium. The Rocky Flats plant near Boulder, Colorado, was built in 1952 for pit production and consequently became the plutonium and beryllium fabrication facility.
The Y-12 plant in Oak Ridge, Tennessee, where mass spectrometers called calutrons had enriched uranium for the Manhattan Project, was redesigned to make secondaries. Fissile U-235 makes the best spark plugs because its critical mass is larger, especially in the cylindrical shape of early thermonuclear secondaries. Early experiments used the two fissile materials in combination, as composite Pu-Oy pits and spark plugs, but for mass production, it was easier to let the factories specialize: plutonium pits in primaries, uranium spark plugs and pushers in secondaries.
Y-12 made lithium-6 deuteride fusion fuel and U-238 parts, the other two ingredients of secondaries.
The Hanford Site near Richland WA operated Plutonium production nuclear reactors and separations facilities during World War 2 and the Cold War. Nine Plutonium production reactors were built and operated there. The first being the B-Reactor which began operations in September 1944 and the last being the N-Reactor which ceased operations in January 1987.
The Savannah River Site in Aiken, South Carolina, also built in 1952, operated nuclear reactors which converted U-238 into Pu-239 for pits, and converted lithium-6 (produced at Y-12) into tritium for booster gas. Since its reactors were moderated with heavy water, deuterium oxide, it also made deuterium for booster gas and for Y-12 to use in making lithium-6 deuteride.
Warhead design safetyEdit
Because even low-yield nuclear warheads have astounding destructive power, weapon designers have always recognised the need to incorporate mechanisms and associated procedures intended to prevent accidental detonation.
It is inherently dangerous to have a weapon containing a quantity and shape of fissile material which can form a critical mass through a relatively simple accident. Because of this danger, the propellant in Little Boy (four bags of cordite) was inserted into the bomb in flight, shortly after takeoff on August 6, 1945. This was the first time a gun-type nuclear weapon had ever been fully assembled.
If the weapon falls into water, the moderating effect of the water can also cause a criticality accident, even without the weapon being physically damaged. Similarly, a fire caused by an aircraft crashing could easily ignite the propellant, with catastrophic results. Gun-type weapons have always been inherently unsafe.
In-flight pit insertionEdit
Neither of these effects is likely with implosion weapons since there is normally insufficient fissile material to form a critical mass without the correct detonation of the lenses. However, the earliest implosion weapons had pits so close to criticality that accidental detonation with some nuclear yield was a concern.
On August 9, 1945, Fat Man was loaded onto its airplane fully assembled, but later, when levitated pits made a space between the pit and the tamper, it was feasible to use in-flight pit insertion. The bomber would take off with no fissile material in the bomb. Some older implosion-type weapons, such as the US Mark 4 and Mark 5, used this system.
In-flight pit insertion will not work with a hollow pit in contact with its tamper.
Steel ball safety methodEdit
As shown in the diagram above, one method used to decrease the likelihood of accidental detonation employed metal balls. The balls were emptied into the pit: this prevented detonation by increasing the density of the hollow pit, thereby preventing symmetrical implosion in the event of an accident. This design was used in the Green Grass weapon, also known as the Interim Megaton Weapon, which was used in the Violet Club and Yellow Sun Mk.1 bombs.
Chain safety methodEdit
Alternatively, the pit can be "safed" by having its normally hollow core filled with an inert material such as a fine metal chain, possibly made of cadmium to absorb neutrons. While the chain is in the center of the pit, the pit can not be compressed into an appropriate shape to fission; when the weapon is to be armed, the chain is removed. Similarly, although a serious fire could detonate the explosives, destroying the pit and spreading plutonium to contaminate the surroundings as has happened in several weapons accidents, it could not cause a nuclear explosion.
While the firing of one detonator out of many will not cause a hollow pit to go critical, especially a low-mass hollow pit that requires boosting, the introduction of two-point implosion systems made that possibility a real concern.
In a two-point system, if one detonator fires, one entire hemisphere of the pit will implode as designed. The high-explosive charge surrounding the other hemisphere will explode progressively, from the equator toward the opposite pole. Ideally, this will pinch the equator and squeeze the second hemisphere away from the first, like toothpaste in a tube. By the time the explosion envelops it, its implosion will be separated both in time and space from the implosion of the first hemisphere. The resulting dumbbell shape, with each end reaching maximum density at a different time, may not become critical.
Unfortunately, it is not possible to tell on the drawing board how this will play out. Nor is it possible using a dummy pit of U-238 and high-speed x-ray cameras, although such tests are helpful. For final determination, a test needs to be made with real fissile material. Consequently, starting in 1957, a year after Swan, both labs began one-point safety tests.
Out of 25 one-point safety tests conducted in 1957 and 1958, seven had zero or slight nuclear yield (success), three had high yields of 300 t to 500 t (severe failure), and the rest had unacceptable yields between those extremes.
Of particular concern was Livermore's W47, which generated unacceptably high yields in one-point testing. To prevent an accidental detonation, Livermore decided to use mechanical safing on the W47. The wire safety scheme described below was the result.
When testing resumed in 1961, and continued for three decades, there was sufficient time to make all warhead designs inherently one-point safe, without need for mechanical safing.
Wire safety methodEdit
In the last test before the 1958 moratorium the W47 warhead for the Polaris SLBM was found to not be one-point safe, producing an unacceptably high nuclear yield of 400 lb (180 kg) of TNT equivalent (Hardtack II Titania). With the test moratorium in force, there was no way to refine the design and make it inherently one-point safe. A solution was devised consisting of a boron-coated wire inserted into the weapon's hollow pit at manufacture. The warhead was armed by withdrawing the wire onto a spool driven by an electric motor. Once withdrawn, the wire could not be re-inserted. The wire had a tendency to become brittle during storage, and break or get stuck during arming, preventing complete removal and rendering the warhead a dud. It was estimated that 50–75% of warheads would fail. This required a complete rebuild of all W47 primaries. The oil used for lubricating the wire also promoted corrosion of the pit.
Under the strong link/weak link system, "weak links" are constructed between critical nuclear weapon components (the "hard links"). In the event of an accident the weak links are designed to fail first in a manner that precludes energy transfer between them. Then, if a hard link fails in a manner that transfers or release energy, energy can't be transferred into other weapon systems, potentially starting a nuclear detonation. Hard links are usually critical weapon components that have been hardened to survive extreme environments, while weak links can be both components deliberately inserted into the system to act as a weak link and critical nuclear components that can fail predictably.
An example of a weak link would be an electrical connector that contains electrical wires made from a low melting point alloy. During a fire, those wires would melt breaking any electrical connection.
Permissive Action LinkEdit
A Permissive Action Link is an access control device designed to prevent unauthorised use of a nuclear weapons. Early PALs were simple electromechanical switches and have evolved into complex arming systems that include integrated yield control options, lockout devices and anti-tamper devices.
- Cohen, Sam, The Truth About the Neutron Bomb: The Inventor of the Bomb Speaks Out, William Morrow & Co., 1983
- Coster-Mullen, John, "Atom Bombs: The Top Secret Inside Story of Little Boy and Fat Man", Self-Published, 2011
- Glasstone, Samuel and Dolan, Philip J., editors, The Effects of Nuclear Weapons (third edition) (PDF), U.S. Government Printing Office, 1977.
- Grace, S. Charles, Nuclear Weapons: Principles, Effects and Survivability (Land Warfare: Brassey's New Battlefield Weapons Systems and Technology, vol 10)
- Hansen, Chuck, "Swords of Armageddon: U.S. Nuclear Weapons Development since 1945" (CD-ROM & download available). PDF. 2,600 pages, Sunnyvale, California, Chucklea Publications, 1995, 2007. ISBN 978-0-9791915-0-3 (2nd Ed.)
- The Effects of Nuclear War, Office of Technology Assessment (May 1979).
- Rhodes, Richard. The Making of the Atomic Bomb. Simon and Schuster, New York, (1986 ISBN 978-0-684-81378-3)
- Rhodes, Richard. Dark Sun: The Making of the Hydrogen Bomb. Simon and Schuster, New York, (1995 ISBN 978-0-684-82414-7)
- Smyth, Henry DeWolf, Atomic Energy for Military Purposes, Princeton University Press, 1945. (see: Smyth Report)
- The physics package is the nuclear explosive module inside the bomb casing, missile warhead, or artillery shell, etc., which delivers the weapon to its target. While photographs of weapon casings are common, photographs of the physics package are quite rare, even for the oldest and crudest nuclear weapons. For a photograph of a modern physics package see W80.
- Life Editors (1961), "To the Outside World, a Superbomb more Bluff than Bang", Life, New York (Vol. 51, No. 19, November 10, 1961), pp. 34–37, retrieved 2010-06-28. Article on the Soviet Tsar Bomba test. Because explosions are spherical in shape and targets are spread out on the relatively flat surface of the earth, numerous smaller weapons cause more destruction. From page 35: "... five five-megaton weapons would demolish a greater area than a single 50-megatonner."
- The United States and the Soviet Union were the only nations to build large nuclear arsenals with every possible type of nuclear weapon. The U.S. had a four-year head start and was the first to produce fissile material and fission weapons, all in 1945. The only Soviet claim for a design first was the Joe 4 detonation on August 12, 1953, said to be the first deliverable hydrogen bomb. However, as Herbert York first revealed in The Advisors: Oppenheimer, Teller and the Superbomb (W.H. Freeman, 1976), it was not a true hydrogen bomb (it was a boosted fission weapon of the Sloika/Alarm Clock type, not a two-stage thermonuclear). Soviet dates for the essential elements of warhead miniaturization – boosted, hollow-pit, two-point, air lens primaries – are not available in the open literature, but the larger size of Soviet ballistic missiles is often explained as evidence of an initial Soviet difficulty in miniaturizing warheads.
- fr 971324, Caisse Nationale de la Recherche Scientifique (National Fund for Scientific Research), "Perfectionnements aux charges explosives (Improvements to explosive charges)", issued 12 July 1950 .[permanent dead link]
- The main source for this section is Samuel Glasstone and Philip Dolan, The Effects of Nuclear Weapons, Third Edition, 1977, U.S. Dept of Defense and U.S. Dept of Energy (see links in General References, below), with the same information in more detail in Samuel Glasstone, Sourcebook on Atomic Energy, Third Edition, 1979, U.S. Atomic Energy Commission, Krieger Publishing.
- Glasstone and Dolan, Effects, p. 12.
- Glasstone, Sourcebook, p. 503.
- "neutrons carry off most of the reaction energy", Glasstone and Dolan, Effects, p. 21.
- Glasstone and Dolan, Effects, p. 21.
- Martin, James E. Physics for Radiation Protection. WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim, 2006, p. 195.
- Glasstone and Dolan, Effects, pp. 12–13. When 454 g (one pound) of U-235 undergoes complete fission, the yield is 8 kilotons. The 13 to 16-kiloton yield of the Little Boy bomb was therefore produced by the fission of no more than 2 pounds (910 g) of U-235, out of the 141 pounds (64,000 g) in the pit. Thus, the remaining 139 pounds (63 kg), 98.5% of the total, contributed nothing to the energy yield.
- Compere, A.L., and Griffith, W.L. 1991. "The U.S. Calutron Program for Uranium Enrichment: History,. Technology, Operations, and Production. Report", ORNL-5928, as cited in John Coster-Mullen, "Atom Bombs: The Top Secret Inside Story of Little Boy and Fat Man", 2003, footnote 28, p. 18. The total wartime output of Oralloy produced at Oak Ridge by July 28, 1945 was 165 pounds (74.68 kg). Of this amount, 84% was scattered over Hiroshima (see previous footnote).
- Hoddeson, Lillian; et al. (2004). Critical Assembly: A Technical History of Los Alamos During the Oppenheimer Years, 1943–1945. Cambridge University Press. p. 271. ISBN 978-0-521-54117-6.
- "Restricted Data Declassification Decisions from 1945 until Present" Archived April 23, 2016, at the Wayback Machine – "Fact that plutonium and uranium may be bonded to each other in unspecified pits or weapons."
- "Restricted Data Declassification Decisions from 1946 until Present". Retrieved 7 October 2014.
- Fissionable Materials Archived October 3, 2006, at the Wayback Machine section of the Nuclear Weapons FAQ,[dead link] Carey Sublette, accessed Sept 23, 2006
- All information on nuclear weapon tests comes from Chuck Hansen, The Swords of Armageddon: U.S. Nuclear Weapons Development since 1945, October 1995, Chucklea Productions, Volume VIII, p. 154, Table A-1, "U.S. Nuclear Detonations and Tests, 1945–1962".
- Nuclear Weapons FAQ: 220.127.116.11 Hybrid Assembly Techniques Archived April 19, 2016, at the Wayback Machine, accessed December 1, 2007. Drawing adapted from the same source.
- Nuclear Weapons FAQ: 18.104.22.168.2.4 Cylindrical and Planar Shock Techniques Archived April 19, 2016, at the Wayback Machine, accessed December 1, 2007.
- "Restricted Data Declassification Decisions from 1946 until Present", Section V.B.2.k Archived April 23, 2016, at the Wayback Machine "The fact of use in high explosive assembled (HEA) weapons of spherical shells of fissile materials, sealed pits; air and ring HE lenses", declassified November 1972.
- Sublette, Carey. "Fission-Fusion Hybrid Weapons". nuclearweaponarchive.
- "Weapons of Mass Destruction (WMD)". globalsecurity.org.
- Cozzani, Franco. "FISSION, FUSION AND STAGING". IERI.
- So I pieced together from Edward's testament and from his memoir that Stan had come to him in February of 1951 American Institute of Physics interview with Richard Garwin by Ken Ford, dated December 2012
- he was going to use first hydrodynamics and just the shockwaves and then neutron heating, which would have been a disaster. It would have blown it up before it got going. It was Teller who came up with the radiation., American Institute of Physics interview with Marshall Rosenbluth by Kai-Henrik Barth, dated August 2003
- 4.4 Elements of Thermonuclear Weapon Design Archived March 11, 2016, at the Wayback Machine. Nuclearweaponarchive.org. Retrieved on 2011-05-01.
- Until a reliable design was worked out in the early 1950s, the hydrogen bomb (public name) was called the superbomb by insiders. After that, insiders used a more descriptive name: two-stage thermonuclear. Two examples. From Herb York, The Advisors, 1976, "This book is about ... the development of the H-bomb, or the superbomb as it was then called." p. ix, and "The rapid and successful development of the superbomb (or super as it came to be called) ..." p. 5. From National Public Radio Talk of the Nation, November 8, 2005, Siegfried Hecker of Los Alamos, "the hydrogen bomb – that is, a two-stage thermonuclear device, as we referred to it – is indeed the principal part of the US arsenal, as it is of the Russian arsenal."
- Howard Morland, "Born Secret", Cardozo Law Review, March 2005, pp. 1401–1408.
- Kemp, Ted (3 September 2017). "North Korea hydrogen bomb: Read the full announcement from Pyongyang". CNBC News. Retrieved 5 September 2017.
- "Israel's Nuclear Weapon Capability: An Overview". www.wisconsinproject.org. Archived from the original on 2015-04-29. Retrieved 2016-10-03.
- "Improved Security, Safety & Manufacturability of the Reliable Replacement Warhead", NNSA March 2007.
- A 1976 drawing Archived April 3, 2016, at the Wayback Machine which depicts an interstage that absorbs and re-radiates x-rays. From Howard Morland, "The Article", Archived March 22, 2016, at the Wayback Machine Cardozo Law Review, March 2005, p. 1374.
- Ian Sample (6 March 2008). "Technical hitch delays renewal of nuclear warheads for Trident". The Guardian.
- "ArmsControlWonk: FOGBANK" Archived January 14, 2010, at the Wayback Machine, March 7, 2008. (Accessed 2010-04-06)
- "SAND8.8 – 1151 Nuclear Weapon Data – Sigma I", Archived April 23, 2016, at the Wayback Machine Sandia Laboratories, September 1988.
- The Greenpeace drawing. Archived March 15, 2016, at the Wayback Machine From Morland, Cardozo Law Review, March 2005, p. 1378.
- Herbert York, The Advisors: Oppenheimer, Teller and the Superbomb (1976).
- "The 'Alarm Clock' ... became practical only by the inclusion of Li6 (in 1950) and its combination with the radiation implosion." Hans A. Bethe, Memorandum on the History of Thermonuclear Program Archived March 4, 2016, at the Wayback Machine, May 28, 1952.
- Rhodes 1995, p. 256.
- See map.
- The Soviet Program for Peaceful Uses of Nuclear Explosions Archived March 13, 2016, at the Wayback Machine by Milo D. Nordyke. Science & Global Security, 1998, Volume 7, pp. 1–117
- 4.5 Thermonuclear Weapon Designs and Later Subsections Archived March 3, 2016, at the Wayback Machine. Nuclearweaponarchive.org. Retrieved on 2011-05-01.
- Operation Hardtack I Archived September 10, 2016, at the Wayback Machine. Nuclearweaponarchive.org. Retrieved on 2011-05-01.
- Operation Redwing Archived September 10, 2016, at the Wayback Machine. Nuclearweaponarchive.org. Retrieved on 2011-05-01.
- Barnaby, Frank (2012). The Role and Control of Weapons in the 1990s. ISBN 978-1134901913.
- "Bulletin of the Atomic Scientists". Educational Foundation for Nuclear Science, Inc. March 1991.
- SDI : Technology, survivability, and software. ISBN 978-1428922679.
- Barnaby, Frank (2012). The Role and Control of Weapons in the 1990s. ISBN 978-1134901913.
- Gsponer, Andre (2005). "Fourth Generation Nuclear Weapons: Military effectiveness and collateral effects". arXiv:physics/0510071.
- Ramsey, Syed (2016). Tools of War: History of Weapons in Modern Times. ISBN 978-9386019837.
- "Details on antimatter triggered fusion bombs". 2015-09-22.
- Weapon and Technology: 4th Generation Nuclear Nanotech Weapons Archived September 24, 2014, at the Wayback Machine. Weapons.technology.youngester.com (2010-04-19). Retrieved on 2011-05-01.
- Fourth Generation Nuclear Weapons Archived March 23, 2016, at the Wayback Machine. Nuclearweaponarchive.org. Retrieved on 2011-05-01.
- Never say "never" Archived April 18, 2016, at the Wayback Machine. Whyfiles.org. Retrieved on 2011-05-01.
- "Mini-nukes and inspect bot weapons being primed for future warfare". 2017-03-17.
- Samuel Glasstone, The Effects of Nuclear Weapons, 1962, Revised 1964, U.S. Dept of Defense and U.S. Dept of Energy, pp. 464–65. This section was removed from later editions, but, according to Glasstone in 1978, not because it was inaccurate or because the weapons had changed.
- "Nuclear Weapons FAQ: 1.6".
- Ramzaev, V; Repin, V; Medvedev, A; Khramtsov, E; Timofeeva, M; Yakovlev, V (2011). "Radiological investigations at the "Taiga" nuclear explosion site: Site description and in situ measurements". Journal of Environmental Radioactivity. 102 (7): 672–80. doi:10.1016/j.jenvrad.2011.04.003. PMID 21524834.
- Ramzaev, V; Repin, V; Medvedev, A; Khramtsov, E; Timofeeva, M; Yakovlev, V (2012). "Radiological investigations at the "Taiga" nuclear explosion site, part II: man-made γ-ray emitting radionuclides in the ground and the resultant kerma rate in air". Journal of Environmental Radioactivity. 109: 1–12. doi:10.1016/j.jenvrad.2011.12.009. PMID 22541991.
- "Why the H-Bomb Is Now Called the 3-F". Life Magazine. Time Inc: 54–55. December 5, 1955.
- Winterberg, Friedwardt (2010). The Release of Thermonuclear Energy by Inertial Confinement: Ways Towards Ignition. World Scientific. pp. 192–93. ISBN 978-9814295918.
- Croddy, Eric A.; Wirtz, James J.; Larsen, Jeffrey, Eds. (2005). Weapons of Mass Destruction: An Encyclopedia of Worldwide Policy, Technology, and History. ABC-CLIO, Inc. p. 376. ISBN 978-1-85109-490-5.
- How much large can bombs be made through staging? One often finds claims on the public Internet that multiple stages could be combined one after the other, in an arbitrary large number, and that therefore the in-principle yield of a thermonuclear could be increased without limit. Such authors usually conclude this argument with the wise statement that nuclear weapons were made already so destructive, that no one could possibly think of increasing their yield even further, or that their military use would be pointless...The idea of adding four, ten, a hundred stages, in a disciplined and well orderly way, driving a larger radiation-driven implosion after the other sounds much more like a sheer nonsense than an in-principle design for an Armageddon-class weapon. It should be added that, to the best knowledge of this author, statements about the actual yield of the most powerful weapons in the U.S. nuclear arsenal, either deployed or envisaged at some stage, were declassified, but no detailed hints at triple staging were released in the open from official sources. Also, there are (convincing) well-known sketches and some reasonable-looking calculations in the open literature about two-stage weapons, but no similarly accurate descriptions of true three stages concepts. "Fission, Fusion and Staging | Ieri". Archived from the original on 2016-03-05. Retrieved 2013-05-22..
- The Air Force and Strategic Detterence 1951–1960. USAF historical division Liaison Office by George F. Lemmer 1967, p. 13. Formerly restricted data Archived June 17, 2014, at the Wayback Machine.
- Bowen and Little, "AF Atomic Energy Program" Vol I–V RS. Authors: Lee Bowen and Stuart Little.
- "Archived copy" (PDF). Archived (PDF) from the original on 2016-03-04. Retrieved 2014-10-06.CS1 maint: archived copy as title (link)
- "Archived copy" (PDF). Archived (PDF) from the original on 2016-10-25. Retrieved 2016-10-25.CS1 maint: archived copy as title (link)
- "A new use for nuclear weapons: hunting rogue asteroids A persistent campaign by weapons designers to develop a nuclear defense against extraterrestrial rocks slowly wins government support 2013". Center for Public Integrity. 2013-10-16. Retrieved 7 October 2014.
- Jason Mick (October 17, 2013). "The mother of all bombs would sit in wait in an orbitary platform". Archived from the original on October 9, 2014.
- planetary defense workshop LLNL 1995
- Weaver, Thomas A; Wood, Lowell (1979). "Necessary conditions for the initiation and propagation of nuclear-detonation waves in plane atmospheres Phys. Rev. A 20, 316 – Published 1 July 1979 Thomas A. Weaver and Lowell Wood". Physical Review A. 20: 316–28. doi:10.1103/PhysRevA.20.316.
- "Neutron bomb: Why 'clean' is deadly". BBC News. July 15, 1999. Retrieved January 6, 2010.
- Broad, William J. (7 September 1999), "Spies versus sweat, the debate over China's nuclear advance", The New York Times, p. 1. The front page drawing Archived May 5, 2016, at the Wayback Machine was similar to one that appeared four months earlier in the San Jose Mercury News.
- Jonathan Medalia, "The Reliable Replacement Warhead Program: Background and Current Developments", CRS Report RL32929 Archived March 11, 2016, at the Wayback Machine, Dec 18, 2007, p CRS-11.
- Richard Garwin, "Why China Won't Build U.S. Warheads" Archived November 5, 2005, at the Wayback Machine, Arms Control Today, April–May 1999.
- Home – NNSA Archived April 1, 2007, at the Wayback Machine
- DoE Fact Sheet: Reliable Replacement Warhead Program Archived August 20, 2008, at the Wayback Machine
- William J. Broad, "The Hidden Travels of The Bomb: Atomic insiders say the weapon was invented only once, and its secrets were spread around the globe by spies, scientists and the covert acts of nuclear states", New York Times, December 9, 2008, p. D1.
- Server, Robert (1992). The Los Alamos Primer (1st ed.). Berkeley: University of California Press. ISBN 978-0520075764.
- Sybil Francis, Warhead Politics: Livermore and the Competitive System of Nuclear Warhead Design, UCRL-LR-124754, June 1995, Ph.D. Dissertation, Massachusetts Institute of Technology, available from National Technical Information Service. This 233-page thesis was written by a weapons-lab outsider for public distribution. The author had access to all the classified information at Livermore that was relevant to her research on warhead design; consequently, she was required to use non-descriptive code words for certain innovations.
- Walter Goad, Declaration for the Wen Ho Lee case Archived March 8, 2016, at the Wayback Machine, May 17, 2000. Goad began thermonuclear weapon design work at Los Alamos in 1950. In his Declaration, he mentions "basic scientific problems of computability which cannot be solved by more computing power alone. These are typified by the problem of long range predictions of weather and climate, and extend to predictions of nuclear weapons behavior. This accounts for the fact that, after the enormous investment of effort over many years, weapons codes can still not be relied on for significantly new designs."
- Chuck Hansen, The Swords of Armageddon, Volume IV, pp. 211–212, 284.
- Hansen, Chuck (1995). Swords of Armageddon. IV. Retrieved 2016-05-20.
- Hansen, Chuck (1995). Swords of Armageddon. III. Retrieved 2016-05-20.
- Dr. John C. Clark, as told to Robert Cahn, "We Were Trapped by Radioactive Fallout", The Saturday Evening Post, July 20, 1957, pp. 17–19, 69–71.
- Rhodes, Richard (1995). Dark Sun; the Making of the Hydrogen Bomb. Simon and Schuster. p. 541.CS1 maint: ref=harv (link)
- Chuck Hansen, The Swords of Armageddon, Volume VII, pp. 396–397.
- Sybil Francis, Warhead Politics, pp. 141, 160.
- Harvey, John R.; Michalowski, Stefan (1994). "Nuclear Weapons Safety:The Case of Trident" (PDF). Science & Global Security. 4.
- . ISBN 978-0521054010 https://books.google.com/?id=95eoQSNDp6gC&pg=PA214&dq=warhead+corrosion&cd=2#v=onepage&q=&f=false. Missing or empty
|title=(help).[permanent dead link]
|Wikimedia Commons has media related to Nuclear weapon design.|
- Carey Sublette's Nuclear Weapon Archive is a reliable source of information and has links to other sources.
- Nuclear Weapons Frequently Asked Questions: Section 4.0 Engineering and Design of Nuclear Weapons
- The Federation of American Scientists provides solid information on weapons of mass destruction, including nuclear weapons and their effects
- Globalsecurity.org provides a well-written primer in nuclear weapons design concepts (site navigation on righthand side).
- More information on the design of two-stage fusion bombs
- Militarily Critical Technologies List (MCTL), Part II (1998) (PDF) from the US Department of Defense at the Federation of American Scientists website.
- "Restricted Data Declassification Decisions from 1946 until Present", Department of Energy report series published from 1994 until January 2001 which lists all known declassification actions and their dates. Hosted by Federation of American Scientists.
- The Holocaust Bomb: A Question of Time is an update of the 1979 court case USA v. The Progressive, with links to supporting documents on nuclear weapon design.
- Annotated bibliography on nuclear weapons design from the Alsos Digital Library for Nuclear Issues
- The Woodrow Wilson Center's Nuclear Proliferation International History Project or NPIHP is a global network of individuals and institutions engaged in the study of international nuclear history through archival documents, oral history interviews and other empirical sources.