Angle of repose
The angle of repose, or critical angle of repose, of a granular material is the steepest angle of descent or dip relative to the horizontal plane to which a material can be piled without slumping. At this angle, the material on the slope face is on the verge of sliding. The angle of repose can range from 0° to 90°. The morphology of the material affects the angle of repose; smooth, rounded sand grains cannot be piled as steeply as can rough, interlocking sands. The angle of repose can also be affected by additions of solvents. If a small amount of water is able to bridge the gaps between particles, electrostatic attraction of the water to mineral surfaces will increase the angle of repose, and related quantities such as the soil strength.
When bulk granular materials are poured onto a horizontal surface, a conical pile will form. The internal angle between the surface of the pile and the horizontal surface is known as the angle of repose and is related to the density, surface area and shapes of the particles, and the coefficient of friction of the material. Material with a low angle of repose forms flatter piles than material with a high angle of repose.
The term has a related usage in mechanics, where it refers to the maximum angle at which an object can rest on an inclined plane without sliding down. This angle is equal to the arctangent of the coefficient of static friction μs between the surfaces.
Applications of theoryEdit
The angle of repose is sometimes used in the design of equipment for the processing of particulate solids. For example, it may be used to design an appropriate hopper or silo to store the material, or to size a conveyor belt for transporting the material. It can also be used in determining whether or not a slope (of a stockpile, or uncompacted gravel bank, for example) will likely collapse; the talus slope is derived from angle of repose and represents the steepest slope a pile of granular material will take. This angle of repose is also crucial in correctly calculating stability in vessels.
There are numerous methods for measuring angle of repose and each produces slightly different results. Results are also sensitive to the exact methodology of the experimenter. As a result, data from different labs are not always comparable. One method is the triaxial shear test, another is the direct shear test.
If the coefficient of static friction is known of a material, then a good approximation of the angle of repose can be made with the following function. This function is somewhat accurate for piles where individual objects in the pile are minuscule and piled in random order.
where, μs is the coefficient of static friction, and θ is the angle of repose.
Methods in determining the angle of reposeEdit
The measured angle of repose may vary with the method used.
Tilting box methodEdit
This method is appropriate for fine-grained, non-cohesive materials with individual particle size less than 10 mm. The material is placed within a box with a transparent side to observe the granular test material. It should initially be level and parallel to the base of the box. The box is slowly tilted until the material begins to slide in bulk, and the angle of the tilt is measured.
Fixed funnel methodEdit
The material is poured through a funnel to form a cone. The tip of the funnel should be held close to the growing cone and slowly raised as the pile grows, to minimize the impact of falling particles. Stop pouring the material when the pile reaches a predetermined height or the base a predetermined width. Rather than attempt to measure the angle of the resulting cone directly, divide the height by half the width of the base of the cone. The inverse tangent of this ratio is the angle of repose.
Revolving cylinder methodEdit
The material is placed within a cylinder with at least one transparent end. The cylinder is rotated at a fixed speed and the observer watches the material moving within the rotating cylinder. The effect is similar to watching clothes tumble over one another in a slowly rotating clothes dryer. The granular material will assume a certain angle as it flows within the rotating cylinder. This method is recommended for obtaining the dynamic angle of repose, and may vary from the static angle of repose measured by other methods.
Of various materialsEdit
Here is a list of various materials and their angle of repose. All measurements are approximated.
|Material (condition)||Angle of Repose (degrees)|
|Bark (wood refuse)||45°|
|Clay (dry lump)||25–40°|
|Clay (wet excavated)||15°|
|Coffee bean (fresh)||35–45°|
|Gravel (crushed stone)||45°|
|Gravel (natural w/ sand)||25–30°|
|Sand (water filled)||15–30°|
|Urea (Granular)||27° |
With different supportsEdit
|Support format||Support||Angle of repose|
Exploitation by antlion and wormlion (Vermileonidae) larvaeEdit
The larvae of the antlions and the unrelated wormlions Vermileonidae trap small insects such as ants by digging conical pits in loose sand, such that the slope of the walls is effectively at the critical angle of repose for the sand. They achieve this by flinging the loose sand out of the pit and permitting the sand to settle at its critical angle of repose as it falls back. Thus, when a small insect, commonly an ant, blunders into the pit, its weight causes the sand to collapse below it, drawing the victim toward the center where the predator that dug the pit lies in wait under a thin layer of loose sand. The larva assists this process by vigorously flicking sand out from the center of the pit when it detects a disturbance. This undermines the pit walls and causes them to collapse toward the center. The sand that the larva flings also pelts the prey with so much loose, rolling material as to prevent it from getting any foothold on the easier slopes that the initial collapse of the slope has presented. The combined effect is to bring the prey down to within grasp of the larva, which then can inject venom and digestive fluids.
The angle of repose plays a part in several topics of technology and science, including:
- Mehta, A.; Barker, G. C. (1994). "The dynamics of sand". Reports on Progress in Physics. 57 (4): 383. Bibcode:1994RPPh...57..383M. doi:10.1088/0034-4885/57/4/002.
- Nichols, E. L.; Franklin, W. S. (1898). The Elements of Physics. Vol. 1. Macmillan. p. 101. LCCN 03027633.
- Glover, T. J. (1995). Pocket Ref. Sequoia Publishing. ISBN 978-1885071002.
- Rikkers, Mark; Rodriguez, Aaron. "Anatomy of an Avalanche". Telluridemagazine.com. Telluride Publishing. Archived from the original on 19 August 2016. Retrieved 3 October 2016.
- "Archived copy" (PDF). Archived from the original (PDF) on 2012-04-12. Retrieved 2013-04-05.CS1 maint: archived copy as title (link)
- Ileleji, K. E.. (2008-10-28). "The angle of repose of bulk corn stover particles". Powder Technology 187 (2): 110–118. doi:10.1016/j.powtec.2008.01.029.
- Lobo-Guerrero, Sebastian. (2007-03-23). "Influence of pile shape and pile interaction on the crushable behavior of granular materials around driven piles: DEM analyses" (em en). Granular Matter 9 (3–4): 241. doi:10.1007/s10035-007-0037-3. ISSN 1434-5021.
- Botz, J. T.; Loudon, C.; Barger, J. B.; Olafsen, J. S.; Steeples, D. W. (2003). "Effects of slope and particle size on ant locomotion: Implications for choice of substrate by antlions". Journal of the Kansas Entomological Society. 76 (3): 426–435.