.338 Lapua Magnum
The .338 Lapua Magnum (8.6×70mm or 8.58×70mm) is a rimless, bottlenecked, centerfire rifle cartridge. It was developed during the 1980s as a high-powered, long-range cartridge for military snipers. It was used in the War in Afghanistan and the Iraq War. As a result of this, it became more widely available. The loaded cartridge is 14.93 mm (0.588 in) in diameter (rim) and 93.5 mm (3.68 in) long. It can penetrate better-than-standard military body armor at ranges up to 1,000 metres (1,090 yd) and has a maximum effective range of about 1,750 metres (1,910 yd) with C.I.P. conform ammunition at sea level conditions. Muzzle velocity is dependent on barrel length, seating depth, and powder charge, and varies from 880 to 915 m/s (2,890 to 3,000 ft/s) for commercial loads with 16.2-gram (250 gr) bullets, which corresponds to about 6,525 J (4,813 ft⋅lbf) of muzzle energy.
|.338 Lapua Magnum|
.338 Lapua Magnum cartridge next to a .338 Norma Magnum
|Place of origin||Finland|
|Used by||Multiple official and civil users|
|Wars||War in Afghanistan|
|Designer||Nammo Lapua Oy|
|Parent case||.416 Rigby, .338/416|
|Case type||Rimless, bottleneck|
|Bullet diameter||8.58 mm (0.338 in)|
|Neck diameter||9.46 mm (0.372 in)|
|Shoulder diameter||13.82 mm (0.544 in)|
|Base diameter||14.91 mm (0.587 in)|
|Rim diameter||14.93 mm (0.588 in)|
|Rim thickness||1.52 mm (0.060 in)|
|Case length||69.20 mm (2.724 in)|
|Overall length||93.50 mm (3.681 in)|
|Case capacity||7.532 cm3 (116.24 gr H2O)|
|Rifling twist||254 mm (1-10")|
|Primer type||Large rifle magnum|
|Maximum pressure||420.00 MPa (60,916 psi)|
|Test barrel length: 690 mm (27.15 inches) Haenel Rs9 and R&S SX1 MTR|
Source(s): Vihta Vuori Powder N570 Lapua (690 mm; 27.15 inches) barrel
British military issue overpressure .338 Lapua Magnum cartridges with a 91.4 mm (3.60 in) overall length, loaded with 16.2-gram (250 gr) LockBase B408 very-low-drag bullets fired at 936 m/s (3,071 ft/s) muzzle velocity. This round, fired from a L115A3 Long Range Rifle, was used in November 2009 by British sniper Corporal of Horse (CoH) Craig Harrison to establish the then-new record for the longest confirmed sniper kill in combat, at a range of 2,475 m (2,707 yd). In reports CoH Harrison mentions the environmental conditions at Musa Qala were perfect for long range shooting: no wind, mild weather, clear visibility.
In addition to its military role, it is increasingly used by hunters and civilian long-range shooting enthusiasts. The .338 Lapua Magnum is capable of taking down any game animal, though its suitability for some dangerous game (Cape buffalo, hippopotamus, white rhinoceros, and elephant) is arguable, unless accompanied by a larger "backup" calibre: "There is a huge difference between calibres that will kill an elephant and those that can be relied upon to stop one." In Namibia the .338 Lapua Magnum is legal for hunting Africa's Big five game if the loads have ≥ 5,400 J (3,983 ft⋅lbf) muzzle energy.
In 1983, Research Armament Industries (RAI) in the United States began development of a new, long-range sniper cartridge capable of firing a 16.2-gram (250 gr), 0.338-inch (8.6 mm) diameter bullet at 914 metres per second (3,000 ft/s) that could lethally penetrate five layers of military body armour at 1,000 m (1,094 yd). After preliminary experiments, a .416 Rigby case necked down to take a 0.338-inch (8.6 mm) bullet was selected, since this diameter presents an optimum of sectional density and penetrating capability for practical spin-stabilized rifle bullets (bullets up to about 5 to 5.5 calibers in length).
The .416 Rigby is an English big game cartridge that was designed in 1911 to accommodate 325 MPa (47,137 psi) pressures. One of the disadvantages of these old cartridge cases, which were intended for firing cordite charges instead of modern smokeless powder, is the thickness of the sidewall just forward of the web. During ignition, the cartridge's base, just forward of the bolt face, is not supported.
During the process RAI employed Jim Bell and Brass Extrusion Labs Ltd. (B.E.L.L.) of Bensenville, Illinois, to make the .338/416 or 8.58×71mm cartridge cases, Hornady produced bullets, and RAI built a sniper rifle under contract for the U.S. Navy. RAI found that the BELL cases did not fulfill the requirements, since they were modified low pressure .416 Rigby cases. Pressed by military deadlines RAI looked for another case producer and contacted Lapua of Finland in 1984. RAI was forced to drop out of the program due to financial difficulties. Subsequently, Lapua of Finland put this cartridge into limited production. The .338/416 rifle program was later canceled when the contractors were unable to make the cartridge meet the project's velocity target of 914 m/s (3,000 ft/s) for a 16.2 g (250 gr) bullet, due to excessive pressures rupturing cartridge cases.
The current .338 Lapua Magnum cartridge was developed as a joint venture between the Finnish rifle manufacturer SAKO and the British rifle manufacturer Accuracy International along with the Finnish ammunition manufacturer Lapua, or more officially Nammo Lapua Oy, which since 1998 is part of the Nordic Ammunition Group (Nammo).
Lapua opted to redesign the .338/416 cartridge. In the new case design, particular attention was directed toward thickening and metallurgically strengthening the case's web and sidewall immediately forward of the web. In modern solid head cases, the hardness of the brass is the major factor that determines a case's pressure limit before undergoing plastic deformation. Lapua tackled this problem by creating a hardness distribution ranging from the head and web (hard) to the mouth (soft) as well as a strengthened (thicker) case web and sidewall immediately forward of the web. This resulted in a very pressure resistant case, allowing it to operate at high pressure and come within 15 m/s (50 ft/s) of the original velocity goal. Lapua also designed a 16.2-gram (250 gr) .338 calibre Lock Base B408 full metal jacket bullet, modeled after its .30 calibre Lock Base bullet configuration. The result was the .338 Lapua Magnum cartridge which was registered with C.I.P. (Commission Internationale Permanente pour l'Epreuve des Armes à Feu Portatives) in 1989. With the procurement by the Dutch Army, the cartridge became NATO codified.
The .338 Lapua Magnum fills the gap between weapons chambered for standard military rounds such as the 7.62×51mm NATO and large, heavy rifles firing the .50 BMG cartridge. It also offers an acceptable amount of barrel wear, which is important to military snipers who tend to fire thousands of rounds a year in practice. This was achieved by coupling a sensible case volume (7.40 ml) to bore area (56.86 mm2/0.5686 cm2) ratio (13.01 Oratio) with ample space for loading relatively long slender projectiles that can provide good aerodynamic efficiency and external ballistic performance for the projectile diameter.[notes 1] Like every other comparable large magnum rifle cartridge, the .338 Lapua Magnum presents a stout recoil. An appropriate fitting stock and an effective muzzle brake helps to reduce recoil-induced problems, enabling the operator to fire more rounds before getting too uncomfortable to shoot accurately. Good factory loads, multiple projectile weights and factory special application ammunition are all available.[notes 2]
Due to its growing civilian popularity, several high quality tactical and match (semi) custom bolt actions designed for the .338 Lapua Magnum are becoming available. These (semi) custom bolt actions are used with other high grade rifle and sighting components to build custom sporting and target rifles.
Law enforcement and military usersEdit
- Albania: RENEA—Sako TRG-42
- Australia: Blaser Tactical 2
- Bangladesh:Bangladesh Armed Forces-Accuracy International AWM
- Canada: Canadian Forces—C14 Timberwolf Medium Range Sniper Weapon System (MRSWS)
- Chile: Chilean Army - APR338 and PGM 338 Barrett Model 98B
- Colombia: TAP.
- Czech Republic — Sako TRG-42
- Denmark: Military of Denmark—Sako TRG-42
- Estonia: Military of Estonia reconnaissance units and special forces—Sako TRG-42.
- Finland: Finnish Defence Forces—Sako TRG-42
- France: French Army, GIGN and Commandement des Opérations Spéciales—PGM 338, Sako TRG-42, AWSM
- Georgia: Police and military - Accuracy International AWM and Sako TRG series, as well as Satevari MSWP. Domestic analogue .338 GBM produced by STC Delta
- Germany: Bundeswehr—Haenel RS9 designated as G29 in service with the special forces; replacing the G22, Erma SR-100, AMP Technical Services DSR-1, GOL Sniper Magnum
- Greece: Anti-Terrorist Unit EKAM—Sako TRG-41
- Hungary: Hungarian Police Security Service (Rendészeti Biztonsági Szolgálat) - Unique-Alpine TPG-1 (Taktische Prazisions Gewehr-1)
- Indonesia: Kopassus—Accuracy International AWSM
- Ireland: Irish Army—Accuracy International AWM
- Israel: Infantry - H-S Precision Pro Series 2000 HTR  Special forces—McMillan Tac-338 and PGM 338, YAMAM—Barrett MRAD
- Italy: Sako TRG-42
- Lithuania: Lithuanian Armed Forces—Accuracy International AXMC
- Malaysia: Pasukan Gerakan Khas—Accuracy International AWSM—Accuracy International AX338
- Netherlands: Dutch military—Accuracy International AWSM, Sako TRG-41
- Poland: GROM—Accuracy International AWM, 1 Pułk Specjalny Komandosów
- Russia: Alpha Group and SOBR—Accuracy International AWSM and Sako TRG-42
- Serbia: Special Brigade—Sako TRG-42.
- Singapore: PGM 338
- Slovenia: Military of Slovenia—PGM 338
- Spain: GOE—Sako TRG-41
- Switzerland: Sako TRG-42
- Turkey: Sako TRG-42,
- United Kingdom: British military—Accuracy International AWSM
- United States: US Navy Special Warfare—McMillan Tac-338
The .338 Lapua Magnum has been designated a "cartridge of interest" by the National Defense Industrial Association (NDIA). It is being groomed to replace the .300 Winchester Magnum and the .50 BMG for anti-personnel long-range service in the U.S. military. On June 17, 2008, the U.S. government issued a market survey to support a requirement for a Precision Sniper Rifle (PRS) to possibly replace the currently fielded Bolt Action SOF Sniper Systems MK 13 (.300 Winchester Magnum) and the M40 and M24 (7.62×51mm NATO) chambered to safely fire factory produced "non-wildcat" .338 caliber ammunition. On 7 March 2013, the Remington MSR was declared the winner of the Precision Sniper Rifle competition. Remington announced that the MSR had won on March 8, and it was publicly confirmed on March 9. This was followed by a $79.7 million contract for 5,150 rifles with suppressors, along with 4,696,800 rounds of ammunition to be supplied over the next ten years. The contract was awarded on 12 September 2013. Remington Defense produces the sniper rifles and utilizes two other companies for other system components, with Barnes Bullets for ammunition and Advanced Armament Corporation for muzzle brakes and suppressors; all three companies are subsidiaries of Remington Outdoor Company.
Extremely thick-walled brass results in a 7.40 ml (114 grains H2O) cartridge case capacity for the .338 Lapua Magnum. The exterior shape of the case was designed to promote reliable feeding and extraction in bolt action, semi-automatic, and automatic firearms alike, under extreme conditions.
.338 Lapua Magnum maximum C.I.P. cartridge dimensions. All sizes in millimeters (mm).
Americans would define the shoulder angle at alpha/2 ≈ 20 degrees. The common rifling twist rate for this cartridge is 254 mm (1 in 10 in), 6 grooves, Ø lands = 8.38 mm, Ø grooves = 8.58 mm, land width = 2.79 mm and the primer type is large rifle magnum.
According to the official C.I.P. (Commission Internationale Permanente pour l'Epreuve des Armes à Feu Portatives) decisions and tables edition 2007 the .338 Lapua Magnum case can handle up to 420.00 MPa (60,916 psi) Pmax piezo pressure. This now prevails over the C.I.P. decisions and tables edition 2003, that rated the .338 Lapua Magnum at 470.00 MPa (68,168 psi) Pmax maximum piezo pressure. The 470.00 MPa (68,168 psi) Pmax maximum piezo pressure C.I.P. ruling for the .300 Lapua Magnum cartridge, which is based on the same case, was not accordingly changed. In C.I.P. regulated countries every rifle cartridge combo has to be proofed at 125% of the prevailing maximum C.I.P. pressure to certify for sale to consumers. This means that .338 Lapua Magnum chambered arms in C.I.P. regulated countries are currently (2013) proof tested at 525.00 MPa (76,145 psi) PE piezo pressure.
Lapua has been ambivalent on the maximum piezo pressure of this cartridge. In the article 'From an American dream to a Finnish success story' by Janne Pohjoispää Lapua propagates the C.I.P. 2007 ruling of 420.00 MPa (60,916 psi) maximum piezo pressure. To further complicate matters the mentioned 56,000 CUP C.I.P. copper crusher pressure in this article would translate in ≈ 447.50 MPa (64,904 psi) C.I.P. piezo pressure according to a study on the conversion from CUP to PSI for rifle cartridges by Denton Bramwell. The C.I.P. 2003 ruling of 470.00 MPa (68,168 psi) piezo pressure is corroborated by Lapua Australia in the 'History and development of the .338 Lapua Magnum' article by Alan C. Paulson. A reverse engineering simulation with QuickLOAD internal ballistic software predicted that Lapua load their factory .338 Lapua Magnum ammunition at ≈ 420.00 MPa (60,916 psi) piezo pressure as Alan C. Paulson asserts in his article.
The large boltface combined with the maximum pressure means that the .338 Lapua Magnum should only be chambered in rifles that are capable of handling such large high pressure cartridges and thus high bolt thrust safely. Chambering such powerful super magnum cartridges in rifles intended for normal magnum rifle cartridges and using high pressure loads can cause serious or fatal injury to the shooter and bystanders.
The American .338-378 Weatherby Magnum cartridge introduced in 1998 and the American .338 Remington Ultra Magnum (.338 RUM) cartridge introduced in 2000 are probably the closest ballistic twins of the .338 Lapua Magnum commercially available as of 2007[update]. The .338-378 Weatherby Magnum is however a belted cartridge and the .338 Remington Ultra Magnum is a rebated rim cartridge.
The American SAAMI (Sporting Arms and Ammunition Manufacturers' Institute) has no normal voluntary guidelines for the .338 Lapua Magnum. On 14 January 2013 it opted to use the metric C.I.P. rulings and add some dimensions that have no C.I.P. analog.
Supersonic range performance of the .338 Lapua MagnumEdit
Performance with C.I.P. conforming cartridgesEdit
For a typical .338 Lapua Magnum high end factory military sniper rifle like the Sako TRG-42 with a 690 mm (27.2 in) long 305 mm (1 in 12 inch) rifling twist rate barrel at sea level, 1,500 m (1,640 yd) is considered to be the maximum shooting distance for man sized targets. When using standard Lapua military 16.2 g (250 gr) loads it has a supersonic range of 1,500 m (1,640 yd) under warm summer conditions at a muzzle velocity of 915 m/s (3,000 ft/s). However, to be able to maintain 80 to 90% hit probability on non-moving 45 cm × 90 cm (17.7 in × 35.4 in) reactive army targets, this maximum shooting distance has to be reduced to 1,300 metres (1,422 yd) at freezing point conditions or 1,100 m (1,203 yd) in Arctic winter conditions, when the muzzle velocity may drop to 880 m/s (2,887 ft/s)—i.e. only during optimal warm summer conditions the 1,500 m (1,640 yd) maximum shooting distance is realistically achievable.
Loaded with more aerodynamic very-low-drag bullets such as the traditionally lead cored 19.44 g (300.0 gr) Lapua Scenar GB528 VLD bullet (G1 BC = 0.736) or the Lost River Ballistics J40 .338 17.5 gram (270 gr) CNC manufactured mono-metal bullet (G1 BC = 0.871) the long-range performance and supersonic range of .338 Lapua Magnum rifles can be improved. These longer very-low-drag bullets require a 254 mm (1 in 10 inch) twist rate to stabilize them. Due to the lower practically possible muzzle velocities for a relative heavy bullet like the 19.44 g (300 gr) Lapua Scenar GB528 VLD bullet it gains about 104 m (114 yd) extra supersonic range under International Standard Atmosphere sea level conditions (air density ρ = 1.225 kg/m3) at a muzzle velocity of 837 m/s (2750 ft/s) when compared to the standard 16.2 g (250 gr) Lapua Scenar GB488 VLD at a muzzle velocity of 915 m/s (3002 ft/s). For significant supersonic range improvement the aerodynamic efficiency of the employed bullets has to be significantly improved without sacrificing a lot of practically achievable muzzle velocity - meaning that besides the coefficient of drag of the projectile weight is also an important parameter for its actual downrange flight behavior. The .338 17.5 gram (270 gr) Lost River Ballistic Technologies J40 match bullet made out of a copper-nickel alloy is one of the most aerodynamic .338 calibre bullets available. It has an 1,800 m (1,970 yd) supersonic range under optimal warm summer conditions at a muzzle velocity of 869 m/s (2,850 ft/s). This makes engaging static targets up to 1,800 m (1,970 yd) feasible.
Performance improvement experiments with non-C.I.P.-conforming cartridgesEdit
Improvement beyond this standard while still using standard .338 Lapua Magnum brass is possible, but the bullets have to be very long (over 5.5 calibers in length) and the normal cartridge overall length of 93.5 mm has to be exceeded making such cartridges wildcats. The common 254 mm (1:10 inch) rifling twist rate also has to be tightened to stabilize very long projectiles. Such commercially non-existent cartridges are termed "wildcats". The use of a wildcat .338 Lapua Magnum based cartridge demands the use of a custom or customized rifle with an appropriately cut chamber and fast-twist bore. The firearm action and if a repeating arm is required the magazine(s) must also be able to cope with dimensional increases.
An example of such a special .338 calibre extreme range bullet is the German CNC manufactured mono-metal 18.92 gram (292 gr) LM-105 (Cd = 0.2487 at Mach 2.216 – this drag coefficient and the corresponding G1, G7 and G8 ballistic coefficients are established by Doppler radar measurements). The LM-105 has a supersonic range of ≈ 1,860 metres (2,030 yd) at a muzzle velocity of 915 metres per second (3,002 ft/s) under International Standard Atmosphere sea level conditions (air density ρ = 1.225 kg/m3). The 2010 version of the LM-105 bullet has an overall length of 54.3 millimetres (2.14 in) or 6.33 calibers and derives its exceptional low drag from a radical LD Haack or Sears-Haack profile in the bullet's nose area. Rifles chambered for this wildcat cartridge, with a cartridge overall length of 105 millimetres (4.1 in), and equipped with custom made 178 mm (1:7 inch) progressive twist rate 900 millimetres (35.4 in) long barrels with a 2° cone-angle (the standard C.I.P. cone-angle for the .338 Lapua Magnum is 6°) cone area finished first and second at several long range competitions. Its most recent win (2007) was in an international Special Forces and police sniper competition in Switzerland against rifles chambered for 7.62×51mm NATO up to .50 BMG at ranges from 100 m – 1,500 m (109 yd – 1,640 yd). The LM-105 bullet exhibited its very low wind drift susceptibility notably at ranges beyond 800 metres (870 yd). A real world average G1 BC of ≈ 0.83 or a G7 BC of ≈ 0.42 is commonly adopted by the users of this bullet, for making long range trajectory predictions using ballistics calculators. In contrast the LM-105 designer Lutz Möller originally calculated an optimistic G1 BC of ≈ 0.93 and a supersonic range of ≈ 2,000 metres (2,190 yd) at a muzzle velocity of 915 metres per second (3,002 ft/s) under International Standard Atmosphere sea level conditions (air density ρ = 1.225 kg/m3).
The .343 Lapua Magnum LM-107 was a wildcat cartridge under development based on the standard .338 Lapua Magnum cartridge case. The LM-107 was hoped to boost the ballistic performance of the LM-105 by achieving an increase in supersonic range. The 19.3 g (298 gr) LM-107 projectile design is 59 millimetres (2.3 in) long and has a Haack profiled nose and an Adams profiled tail. The rifling twist rate for the .343 Lapua Magnum LM-107 wildcat cartridge was chosen at 180 mm (1:7 inch), Ø lands = 8.72 mm, Ø grooves = 8.45 mm and loaded with the LM-107 projectile has a cartridge overall length of 107 millimetres (4.2 in). The length of the neck is increased from 8,31 to 8,50 mm to support the bigger LM-107 bullet. Several other dimensions of the .338 Lapua Magnum parental cartridge are also changed. The shoulder angle gets steepened from 40° to 60° and the body taper is set at 1°. The throat area is set at a 2° cone-angle. All this modifications make the .343 Lapua Magnum a fairly comprehensively revised wildcat cartridge. Out of a 900 millimetres (35.4 in) long progressive twist barrel Mr. Möller expected to achieve 909 metres per second (2,982 ft/s) muzzle velocity. If Möller's design assumptions are correct the LM-107 projectile with a calculated G1 BC of 1.02 will offer a supersonic range of ≈ 2,170 metres (2,370 yd) at a muzzle velocity of 909 metres per second (2,982 ft/s) under International Standard Atmosphere sea level conditions (air density ρ = 1.225 kg/m3).
.338 Lapua Magnum as a parent caseEdit
The .300 Lapua MagnumEdit
The commercially successful .338 Lapua Magnum cartridge has functioned as the parent case for the .300 Lapua Magnum, which is essentially a necked-down version of the .338 Lapua Magnum. The .338 cartridge case was used for this since it has the capability to operate with high chamber pressures which, combined with smaller and hence lighter bullets result in very high muzzle velocities.
The Finnish ammunition manufacturer Lapua got the .300 Lapua Magnum C.I.P. certified, so it became an officially registered and sanctioned member of the Finnish "family" of super magnum rifle cartridges. The .300 Lapua Magnum is not commercially available and currently exists only as a C.I.P. datasheet. It is however still used by a few shooters who produce the cases from .338 Lapua Magnum brass by reshaping the shoulder and neck, and handloading it with .30 calibre bullets.
.300 Lapua Magnum maximum C.I.P. cartridge dimensions. All sizes in millimeters (mm).
Americans would define the shoulder angle at alpha/2 ≈ 25 degrees. The common rifling twist rate for this cartridge is 240 mm (1 in 9.45 in), 4 grooves, Ø lands = 7.62 mm, Ø grooves = 7.82 mm, land width = 4.47 mm and the primer type is large rifle magnum.
According to the official C.I.P. (Commission Internationale Permanente pour l'Epreuve des Armes à Feu Portatives) rulings the .300 Lapua Magnum can handle up to 440.00 MPa (63,817 psi) Pmax piezo pressure. This now prevails over the C.I.P. decisions and tables edition 2007, that rated the .300 Lapua Magnum at 470.00 MPa (68,168 psi) Pmax piezo pressure. In C.I.P. regulated countries every rifle cartridge combo has to be proofed at 125% of this maximum C.I.P. pressure to certify for sale to consumers. This means that .300 Lapua Magnum chambered arms in C.I.P. regulated countries are currently (2013) proof tested at 550.00 MPa (79,771 psi) PE piezo pressure.
This for rifles very high maximum allowed chamber pressure level indicates that the cases of the .300 and .338 Lapua Magnum are built extremely sturdy to cope with this for rifles very high operating pressure. The large boltface combined with the high 470 MPa (68,000 PSI) maximum pressure makes that the .300 Lapua Magnum should only be chambered in rifles that are capable of handling such large and fierce cartridges and thus high bolt thrust safely. Chambering such powerful super magnum cartridges in rifles intended for normal magnum rifle cartridges and using 470 MPa (68,000 PSI) loads can cause serious or fatal injury to the shooter and bystanders.
The 7.62 UKMEdit
The .338 Lapua Magnum cartridge is also used as the parent case for the German designed 7.62 UKM, which is essentially a necked-down shortened version of the .338 Lapua Magnum. The use of the .338 cartridge case with its capability to operate at high chamber pressures resulted in magnum case capable of producing high muzzle velocities.
The 7.62 UKM was developed by Michael Uekötter and was C.I.P.-certified in 2002, making it an officially registered and sanctioned member of the Finnish "family" of super magnum rifle cartridges. The 7.62 UKM is not commercially available and currently exists only as a C.I.P. datasheet. It is however still used by a few shooters who produce the cases from .338 Lapua Magnum brass by reshaping the shoulder and neck, and handloading it with .30 calibre bullets.
7.62 UKM maximum C.I.P. cartridge dimensions. All sizes in millimeters (mm).
Americans would define the shoulder angle at alpha/2 ≈ 20 degrees. The common rifling twist rate for this cartridge is 254 mm (1 in 10 in), 6 grooves, Ø lands = 7.62 mm, Ø grooves = 7.82 mm, land width = 2.79 mm and the primer type is large rifle magnum.
According to the official C.I.P. (Commission Internationale Permanente pour l'Epreuve des Armes à Feu Portatives) rulings the 7.62 UKM Magnum can handle up to 440.00 MPa (63,817 psi) Pmax piezo pressure. This now prevails over the C.I.P. decisions and tables edition 2007, that rated the 7.62 UKM at 470.00 MPa (68,168 psi) Pmax piezo pressure. In C.I.P. regulated countries every rifle cartridge combo has to be proofed at 125% of this maximum C.I.P. pressure to certify for sale to consumers. This means that 7.62 UKM chambered arms in C.I.P. regulated countries are currently (2013) proof tested at 550.00 MPa (79,771 psi) PE piezo pressure.
The .338 Lapua Magnum case is also used as the parent case for a host of modified variants that are not officially registered with or sanctioned by C.I.P. or its American equivalent, SAAMI. Such cartridges which use commercial factory cases are generally known as wildcats. By changing the shape of standard factory cases (decreasing case taper and/or changing the shoulder geometry) the wildcatter generally increases the case capacity of the factory parent cartridge case, allowing more propellant to be used to generate higher velocities. Besides changing the shape and internal volume of the parent cartridge case, wildcatters also can change the original calibre. A reason to change the original calibre can be to comply with a minimal permitted calibre or bullet weight for the legal hunting of certain species of game. Because the .338 Lapua offers a large and exceptionally sturdy, pressure resistant cartridge case that can be relatively easily reloaded and hence be reused several times, it has become quite popular amongst wildcatters. With the .338 Lapua Magnum as the parent case wildcatters have created 7 mm (7 mm Allen Magnum, 7 mm Katzmeier, 7 mm Fatso), .30 (.30-338 Lapua (Triebel), .30 Wolf, 300 Allen Express), 8 mm (8 mm-338 Lapua (Triebel), LM-101), .338 (.338 Yogi, LM-105), .343 (.343 Lapua Magnum LM-107), 9.3 mm (9,3-338 Lapua Magnum (Triebel)), .375 (9.5×70 ELR) and .50 calibre (.510 Whisper) variants. Tom Sarver used a .300 Hulk wildcat cartridge, which is basically a necked-down, blown out, shortened .338 Lapua Magnum variant, to achieve a 1.403-inch (35.64 mm) diameter benchrest 5-shot group on 7 July 2007, establishing a world record.
- The Finnish Army found out during a test/trails program and 7 years of service that the barrels of their Sako TRG-42 sniper rifles lasted 7,000 to 8,000 rounds with Lapua Lock Base B408 factory ammunition before showing impermissible accuracy decay. The Finnish Army consistent accuracy requirement for these rifles is ≤ 1 MOA at 1,000 m. If this requirement is not met the TRG-42 gets a new barrel. This is normal practice for active high performance precision rifle operators who regard barrels as expendable items. The continuous use of very powerful handloads (which results in higher muzzle velocities) resulted in much quicker throat erosion reducing the TRG-42 barrel's accuracy life to 1500 to 2000 rounds.
- In 1990, the US military Adjutant General's Office issued a legal opinion holding that the Sierra MatchKing bullet (and similar bullets of other manufacturers), despite being a hollow point design, is not designed specifically to cause greater damage or suffering in a human target, and in fact normally does not create a wound readily distinguishable from wounds caused by conventional full metal jacket bullets, and is therefore in their opinion legal under the Hague Convention for use in war.
- Lapua product brochure .338 Lapua Magnum ammunition Archived September 27, 2011, at the Wayback Machine.
- VihtaVuori international reloading guide 2011 Archived 2011-07-25 at the Wayback Machine.
- .338 Lapua Mag. (8.6x70) Archived 2011-05-02 at the Wayback Machine
- Sheridan, Michael (May 3, 2010). British sniper Craig Harrison (The Silent Assassin) breaks record, kills target from 1.5 miles away" Archived October 18, 2010, at the Wayback Machine. Daily News (New York). Accessed May 13, 2010.
- Alpert, Lukas I. (May 2, 2010). "Sniper kills Qaeda-from 1½ mi. away". New York Post. Accessed May 13, 2010.
- "Super Sniper Kills Taliban 1.5 Miles Away" Archived May 14, 2015, at the Wayback Machine 3 May 2010 Sky News
- Robertson, K: The Perfect Shot, Safari Press, Inc, Long Beach, 1999:p. 50.
- "NAPHA - Namibia Professional Hunting Assiation: Hunting Laws& Rifle Importation". napha-namibia.com. Archived from the original on 23 August 2015. Retrieved 5 July 2015.
- What is the Maximum Length of a spin stabilized Projectile? by Mr. Beat Kneubühl.
- Lapua Oy company website[dead link].
- Barnes, Frank C., Cartridges of the World 8th Edition, edited by M. L. McPherson, DBI Books, 1997, ISBN 0-87349-178-5.
- "From an American dream to a Finnish success story". Archived from the original on 2008-04-30. Retrieved 2009-05-16.
- "History of Lapua - About us - Nammo Lapua". lapua.com. Archived from the original on 2018-01-22. Retrieved 22 February 2017.
- "Cartridges for Long". quarryhs.co.uk. Archived from the original on 27 May 2016. Retrieved 22 February 2017.
- "RECOIL". accuratereloading.com. Archived from the original on 27 October 2016. Retrieved 22 February 2017.
- Sniper Use of Open-Tip Ammunition Archived 2007-04-27 at the Wayback Machine.
- worldrifles.com Archived 2014-10-25 at the Wayback Machine.
- World Small Arms Inventory Archived 2007-05-23 at the Wayback Machine.
- Sako TRG-42 The quest for cold-bore accuracy stops here. By Eric R. Poole, Posted: 2010-04 Archived July 11, 2011, at the Wayback Machine
- Australian Government Contract Notice View - CN68887 BLASER SNIPER RIFLES Archived 2011-07-06 at the Wayback Machine.
- Australian Government Contract Notice View - CN152254 .338 BLASER ITEMS - VARIOUS Archived 2011-07-06 at the Wayback Machine.
- "Blaser". Official website: Equipment and clothing. Australian Army. Archived from the original on 22 March 2012. Retrieved 13 June 2012.
- "PGW Timberwolf". snipershide.com. Archived from the original on 2009-03-18. Retrieved 2009-07-17.
- "Chile's Defense & Military". blogspot.cl. Archived from the original on 1 July 2016. Retrieved 22 February 2017.
- "Indumil – Industria Militar Colombiana". indumil.gov.co. Archived from the original on 25 September 2017. Retrieved 22 February 2017.
- O'Dwyer, Gerard (February 25, 2008). "Finland's Sako Targets Nordic Rifle Sales". Defense News. Retrieved July 31, 2010.
- "Military Issued Sniper Rifles - Sniper Central". snipercentral.com. Archived from the original on 25 October 2014. Retrieved 22 February 2017.
- "Wayback Machine" (PDF). 7 June 2011. Archived from the original (PDF) on 7 June 2011.
- "Estonia to buy sniper rifles from Finland - BONJOUR L'ESTONIE". typepad.com. Archived from the original on 27 September 2007. Retrieved 22 February 2017.
- "სნაიპერული ვაზნა .338 G.B.M". delta.gov.ge. Archived from the original on 2016-08-19. Retrieved 22 February 2017.
- "Aus Suhl an die Spezialkräfte: RS9 wird G29". strategie-technik.blogspot.de. Retrieved 11 December 2016.
- "New German Army G29 Sniper Rifle (Haenel RS9 in .338 LM) - The Firearm Blog". 18 February 2016. Archived from the original on 18 July 2017. Retrieved 17 July 2017.
- "Bolt action precision rifle". Archived from the original on 2017-10-29. Retrieved 2017-07-17.
- "Modern Firearms - ERMA SR-100". guns.ru. Archived from the original on 12 November 2016. Retrieved 22 February 2017.
- "Kopassus & Kopaska - Specijalne Postrojbe Republike Indonezije". Hrvatski vojnik (in Croatian). Archived from the original on 2010-08-22. Retrieved 2010-06-12.
- "isayeret.com - The Israeli Special Forces Database". isayeret.com. Archived from the original on 26 February 2016. Retrieved 22 February 2017.
- "isayeret.com - The Israeli Special Forces Database". isayeret.com. Archived from the original on 25 July 2016. Retrieved 22 February 2017.
- בלומנטל, איתי (1 March 2015). "נחשף פירוט הנשק של הימ"מ". Ynet. Archived from the original on 2 August 2017. Retrieved 22 February 2017 – via Ynet.
- "Incursori IX° Reggimento "COL MOSCHIN"". 10 May 2008. Archived from the original on 10 May 2008. Retrieved 22 February 2017.
- Media, Fresh. "Ministry of National Defence Republic of Lithuania :: News » News Releases". kam.lt. Archived from the original on 5 November 2016. Retrieved 22 February 2017.
- "PGK Malaysian Special Police Force Weapons". Military Factory. March 7, 2016. Archived from the original on January 18, 2017. Retrieved 2016-03-11.
- "Special Forces - Wapens" (in Dutch). Netherlands Legermuseum: Collectie Informatie Centrum. Archived from the original on 2009-02-27. Retrieved 2009-10-17.
- "Accuracy, antipersoneel snipergeweer .338" (in Dutch). Netherlands Ministry of Defence. Archived from the original on December 16, 2011. Retrieved 2010-02-24.
- Nowe gromy GROM Archived 2010-03-26 at the Wayback Machine
- Snipers foto[dead link]
- ""Мой враг — всего лишь мишень. Только живая" - интервью со снайпером "Альфы"". Archived from the original on 2016-01-07. Retrieved 2019-07-29.
- http://slavs.org.ua/sorevnovanie-sniperov(in Russian)[permanent dead link]
- Waffen HQ Russian Infantry weapons Archived 2007-11-12 at the Wayback Machine.
- "Specijalne-jedinice.com - Puške za precizno gađanje "Sako TRG"". specijalne-jedinice.com. Archived from the original on 2 February 2017. Retrieved 22 February 2017.
- "Singapurske specijalne postrojbe". Hrvatski vojnik (in Croatian) (212). October 2008. Archived from the original on 2009-10-15. Retrieved 2009-10-25.
- "8.6 mm Mini Hecate Sniper Rifle". slovenskavojska.si. Archived from the original on 7 March 2017. Retrieved 22 February 2017.
- "Web Del Grupo Especial De Operaciones (GEO)" (in Spanish). www.policia.es - Official Website of the Spanish National Police Corps. Archived from the original on 2011-07-20. Retrieved 2009-06-26.
- "Päätökset". valtioneuvosto.fi. Archived from the original on 2 September 2017. Retrieved 22 February 2017.
- "Wettkampf der Scharfschützen". 24 February 2009. Archived from the original on 24 February 2009. Retrieved 22 February 2017.
- "Turkin armeija ostanut suomalaisia Sako-kiväärejä?". yle.fi. Retrieved 22 February 2017.
- L115A3 Long Range Rifle. British Army. Archived January 6, 2013, at the Wayback Machine
- "Retail Store - McMillan Fiberglass Stocks". mcmfamily.com. Archived from the original on 8 May 2014. Retrieved 22 February 2017.
- Buiso, Gray (January 1, 2012). "Meet the big shot - SEAL is America's deadliest sniper". New York Post. Archived from the original on January 7, 2012. Retrieved 2012-01-03.
- Sanchez, Raf (2 January 2012). "'The Devil of Rahmadi' named America's deadliest sniper". London: The Daily Telegraph. Archived from the original on 4 January 2012. Retrieved 2012-01-02.
- "McMillan TAC-338 Sniper Rifle". Archived from the original on May 15, 2013. Retrieved February 16, 2013.
- US Special Operations Considers A ".338" Sniper Rifle Archived 2008-07-09 at the Wayback Machine.
- Precision Sniper Rifle - Solicitation Number: H92222-09-PSR Archived 2011-05-20 at the Wayback Machine.
- Curtis, Rob (7 March 2013). "SOCOM PSR contract awarded to Remington Defense MSR". Gearscout blog. Military Times. Archived from the original on 14 March 2013. Retrieved 9 March 2013.
- It’s Official: SOCOM PSR Contract awarded to Remington Defense Archived 2013-12-19 at the Wayback Machine - Militarytimes.com/Gearscout, 8 March 2013
- "C.I.P. TDCC sheet 338 Lapua Mag" (PDF). Archived (PDF) from the original on 2014-01-02. Retrieved 2013-02-26.
- From an American dream to a Finnish success story. Archived December 4, 2010, at the Wayback Machine
- Correlating PSI and CUP, a study done that shows a high correlation between CUP and PSI for rifle cartridges by Denton Bramwell Archived 2007-08-20 at the Wayback Machine.
- "History and development of the .338 Lapua Magnum". Archived from the original on 2018-09-03. Retrieved 2018-09-03.
- SAAMI Maximum Cartridge / Minimum Chamber drawing (METRIC) 338 Lapua Magnum, page 116
- "Weapon Employment Zone (WEZ) Analysis of the Optimized 300 Winchester Magnum vs 338 Lapua Magnum With Various Ammunition Types by Bryan Litz, Applied Ballistics LLC" (PDF). Archived from the original (PDF) on 2015-09-23. Retrieved 2014-04-02.
- "Probabalistic Weapon Employment Zone (WEZ) Analysis A Conceptual Overview by Bryan Litz" (PDF). Archived from the original (PDF) on 2015-09-23. Retrieved 2014-04-02.
- "LM-105". Archived from the original on February 9, 2014.
- Progressive twist rate barrels Archived 2015-06-24 at the Wayback Machine.
- LM-107 .343 Lapua Magnum Archived April 2, 2009, at the Wayback Machine
- "C.I.P. TDCC sheet 300 Lapua Mag" (PDF). Archived (PDF) from the original on 2015-07-22. Retrieved 2013-07-14.
- The 7.62 UKM. A German 300 Magnum Wildcat Extraordinary Archived 2008-05-06 at the Wayback Machine.
- "C.I.P. TDCC sheet 7,62 UKM" (PDF). Archived (PDF) from the original on 2014-09-29. Retrieved 2013-07-14.
- The 7mm Fatso - The Ultimate Short Magnum! by Greg Duley Archived 2009-06-14 at the Wayback Machine.
- Sarver Shoots 1.403″ Group at 1000 Yards Archived 2008-09-04 at the Wayback Machine.
|Wikimedia Commons has media related to .338 Lapua Magnum.|
- Lapua official site
- Lapua product brochure .338 Lapua Magnum ammunition[dead link]
- Modern Firearms List of Sniper Rifles
- PGW Defence Technology - Manufacturer (.338 Lapua Magnum and .408 Chey Tac)
- PGWDTI Timberwolf Tactical rifle (.338 Lapua Magnum and .408 Chey Tac chamberings)
- .338 Lapua Magnum reloading data at Reloader's Nest
- Lutz Möller's .338 Lapua Magnum Page
- LM-101 Long Range Bullet for an 8 mm - .338 Lapua Magnum High Performance Wildcat Cartridge
- Lapua 338 Magnum, Exclusive Caliber for The New Age of Sniping
- .338 Lapua Magnum - "Generation II" ordnance development program by Caina Longbranch
- Cartridges for Long-Range Sniping Rifles by Anthony G Williams
- C.I.P. TDCC sheet 338 Lapua Mag.